CONTENTS Technical data…..………………………………………………………... General safety rules…….………………………………………………... Specific safety rules for bench grinder..…………………………………. Electrical information…………………………………………………..... Carton contents.………………………………………………………….. Know your bench grinder………………………………………………... Assembly………………………………………………………………… Operation……………………………………………………………….... Maintenance……………………………………………………………… Exploded view…………………………………………………………… Parts list………………………………………………………………….. Warranty………………………………………………………………….
GENERAL SAFETY RULES GENERAL SAFETY INSTRUCTIONS Operating a bench grinder can be dangerous if safety and common sense are ignored. The operator must be familiar with the operation of the tool. Read this manual to understand this bench grinder. DO NOT operate this Bench Grinder if you do not fully understand the limitations of this tool. DO NOT modify this bench grinder in any way.
12. ALWAYS UNPLUG THE TOOL FROM THE ELECTRICAL RECEPTACLE when making adjustments, changing parts, or performing maintenance. 13. KEEP PROTECTIVE GUARDS IN PLACE AND IN WORKING ORDER. 14. AVOID ACCIDENTAL STARTING. Make sure that the power switch is in the OFF position before plugging in the power cord to the electrical receptacle. 15. REMOVE ALL MAINTENANCE TOOLS from the immediate area prior to turning on the Bench Grinder. 16. USE ONLY RECOMMENDED ACCESSORIES.
SAVE THESE INSTRUCTIONS SPECIFIC SAFETY RULES FOR BENCH GRINDER 1. USE GRINDING WHEELS suitable for the speeds of the grinder. 2. STAND BESIDE the bench grinder during start-up, not directly in front. 3. DO NOT REMOVE THE WHEEL GUARD. 4. DO NOT USE THE GRINDING WHEEL TO CUT ANYTHING. 5. DO NOT USE ANYTHING TO STRESS THE GRINDING WHEEL. 6. USE A GRINDING WHEEL DRESSING TOOL to shape or remove glaze from grinding wheels. 7. ADJUST DISTANCE between wheel and tool rest to maintain at most a 1/8-inch (3.
17. DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center. 18. DO NOT TURN THE MOTOR SWITCH ON AND OFF RAPIDLY. This could cause the wheel to loosen and create a hazard. Should this ever occur, stand clear and allow the wheel to come to a complete stop. Disconnect your grinder from the power supply and retighten the wheel nut securely. 19. RISK OF INJURY DUE TO ACCIDENTAL STARTING. Do not use in an area where children may be present. 20.
33. LAWN MOWER BLADES are usually sharpened on only one edge and dressed up slightly on the other. Perform this sharpening process on both cutting ends of the blade. After sharpening, balance the blade by removing additional material. ELECTRICAL INFORMATION Grounding instructions IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides the path of least resistance for electric current and reduces the risk of electric shock.
Minimum Gauge for Extension Cords (AWG) (When using 120 V only) Ampere Rating 0 – 6 Amps 6 – 10 Amps 10 – 12 Amps 12 – 16 Amps Total Length of Cord in feet 50' 100' 150' 16 gauge 16 gauge 14 gauge 16 gauge 14 gauge 12 gauge 16 gauge 14 gauge 12 gauge 12 gauge Not Recommended 25' 18 gauge 18 gauge 16 gauge 14 gauge Make sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it.
CARTON CONTENTS UNPACKING AND CHECKING CONTENTS This bench grinder requires a minimal amount of assembly: 1. Remove parts from all of the cartons and lay them on a clean work surface. 2. Remove any protective materials and coatings from the bench grinder and its parts. The protective coatings can be removed by spraying on WD-40 and wiping it off with a soft cloth. This may need to be redone several times before all of the protective coatings are removed completely.
KNOW YOUR BENCH GRINDER 6 5 7 4 8 3 2 9 1 11 1 2 3 4 5 6 INNER WHEEL GUARD - Covers the grinding wheels and protects against accidental contact. TOOL RESTS - Used to support the workpiece that is being ground. Adjustable to provide angled surfaces. GRINDING WHEEL 36 GRIT - Used to remove heavy material from workpiece. EYESHIELD - Protective Lexan see-thru shields to prevent any loose debris from contacting the operator. LOCKING KNOB - Lock the eyeshield in position.
ASSEMBLY Warning: To avoid injury from unexpected starting or electrical shock, do not plug the power cord into a source of power during unpacking and assembly. This cord must remain unplugged whenever you are adjusting/assembling the grinder. If any part is missing or damaged, do not attempt to assemble the grinder, or plug in the power cord. TOOL RESTS, SPARK ARRESTORS AND EYE SHIELDS Figure 1 1. Install left tool rest to the left wheel guard.
OPERATION Caution: Keep all bystanders a safe distance away from the tool and not in direct line, front or back of the grinder. 1. Your bench grinder has a medium wheel (60 grit) for medium material removal and general purpose grinding, and a coarse wheel (36 grit) for fast material removal. 2. To operate the bench grinder, always wear safety glasses and turn the tool on while standing at the side of the grinder (as opposed to in front). Allow it to reach full speed before grinding. 3.
Maintenance Warning: For your own safety, turn switch to OFF and remove plug from power source outlet before adjusting and maintaining your bench grinder. If power cord is worn, cut or damaged in any way, have it replaced immediately. 1. Regularly check the tool and use a soft brush to remove accumulated dust. Wear safety goggles to protect your eyes while cleaning. 2. If the body of the grinder needs cleaning, wipe it down with a soft, damp cloth. A mild detergent can be used.
EXPLODED VIEW 14
PARTS LIST Item Stock # Description Item Stock # Description 1 4276-001 Bolt 26 4276-026 Switch 2 4276-002 Spring Washer 27 4276-027 Switch Plate 3 4276-003 Flat Washer 28 4276-028 Fastener Assembly 4 4276-004 Left Eyeshield Bracket 29 4276-029 Bottom Plate 5 4276-005 Left Eyeshield 30 4276-030 Fastener Assembly 6 4276-006 Tool Rest Lock Knob 31 4276-031 Rubber Foot 7 4276-007 Left Tool Rest 32 4276-032 Capacitor 8 4276-008 Nut 33 4276-033 Flat Washer 9
LIMITED TWO YEARS WARRANTY WEN Products is committed to build tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC ("Seller") warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.
