MODEL 48107 ELECTRIC IMPACT WRENCH For replacement parts visit WENPRODUCTS.COM IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions. If you use your tool properly and for its intended purpose, you will enjoy years of safe, reliable service.
TABLE OF CONTENTS Specifications............................................................................................ 2 Introduction.............................................................................................. 3 General Safety Rules................................................................................. 4 Specific Safety Rules for Your Impact Wrench.......................................... 6 Electrical Information.............................................................
INTRODUCTION Thanks for purchasing the WEN Impact Driver. We know you are excited to put your tool to work, but first, please take a moment to read through the manual. Safe operation of this tool requires that you read and understand this operator’s manual and all the labels affixed to the tool. This manual provides information regarding potential safety concerns, as well as helpful assembly and operating instructions for your tool. SAFETY ALERT SYMBOL: Indicates danger, warning, or caution.
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: Read and understand all warnings, cautions and operating instructions before using this tool. Failure to follow all instructions listed below may result in personal injury, electric shock, fire and/or tool damage. WORK AREA SAFETY 1. Keep work area clean and well lit. Cluttered or dark areas invite accidents. 2.
GENERAL SAFETY RULES 6. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. 7. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. POWER TOOL USE AND CARE 1. Do not force the power tool. Use the correct power tool for your application.
SPECIFIC RULES FOR YOUR IMPACT WRENCH WARNING: Do not operate the heat gun until you have read and understood the following instructions and the warning labels. 1. WORK ENVIRONMENT. Do not operate the tool in wet or damp conditions; doing so significantly increases the risk of electrical shock. Do not operate the tool in the presence of flammable liquids or gases. 2. PERSONAL SAFETY. Always wear ANSI Z87.1-approved glasses, hearing protection and dust mask when using the wrench. Tie back long hair.
ELECTRICAL INFORMATION DOUBLE-INSULATED TOOLS The tool’s electrical system is double insulated where two systems of insulation are provided. This eliminates the need for the usual three-wire grounded power cord. Double insulated tools do not need to be grounded, nor should a means for grounding be added to the product. All exposed metal parts are isolated from the internal metal motor components with protecting insulation.
KNOW YOUR IMPACT WRENCH UNPACKING Carefully remove the impact wrench from the packaging. Make sure to take out all contents and accessories. Do not discard the packaging until everything is removed. Check all components and compare against the diagram below. If any part is damaged or missing, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email us at techsupport@wenproducts.com.
OPERATION REMOVING AN ACCESSORY NOTE: The accessory may be warm or hot if it has just been used. Allow it sufficient time to cool down, if necessary. To remove an accessory: 1. Grasp the accessory and firmly pull it off. NOTE: when your impact wrench is new, the hog ring may need to wear in, and it may be very difficult to remove accessories. If you cannot remove an accessory by simply pulling it off: 1. Wiggle the accessory back and forth while pulling to try to work it off the anvil. 2.
MAINTENANCE WARNING: To avoid accidents, turn OFF and unplug the tool from the electrical outlet before cleaning, adjusting, or performing any maintenance work. WARNING: Any attempt to repair or replace electrical parts on this tool may be hazardous. Servicing of the tool must be performed by a qualified technician. When servicing, use only identical WEN replacement parts. Use of other parts may be hazardous or induce product failure.
MAINTENANCE WARNING: To avoid accidents, turn OFF and unplug the tool from the electrical outlet before cleaning, adjusting, or performing any maintenance work. WARNING: Any attempt to repair or replace electrical parts on this tool may be hazardous. Servicing of the tool must be performed by a qualified technician. When servicing, use only identical WEN replacement parts. Use of other parts may be hazardous or induce product failure.
TROUBLESHOOTING GUIDE WARNING: Stop using the tool immediately if any of the following problems occur. Repairs and replacements should only be performed by an authorized technician. For any questions, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email us at techsupport@wenproducts.com. PROBLEM Motor does not start CAUSE Power cord damaged or not properly plugged in. Check the power cord, extension cord, power plug and the power outlet. Make sure the outlet is functional.
EXPLODED VIEW & PARTS LIST 13
EXPLODED VIEW & PARTS LIST No. Part No. Description Qty. No. Part No. Description Qty. 1 48107-001 Plastic Sleeve 1 10 48107-010 Gear Assembly 1 2 48107-002 Screw ST5 x 45 4 48107-010.1 48107-003 1 Needle Bearing Ø12 x Ø8 x 10 2 3 Head Housing Assembly 10.1 10.2 48107-010.2 Gear 1 3.1 48107-003.1 Head Housing 1 11 48107-011 1 3.2 48107-003.2 Sealing Ring 1 Washer Ø8.4 x Ø16 x 0.5 12 48107-012 Motor Inner Cover 1 3.3 48107-003.
WARRANTY STATEMENT WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship during personal use for a period of two (2) years from date of purchase or 500 hours of use; whichever comes first.
THANKS FOR REMEMBERING
