5-IN-1 PNEUMATIC TOOL Model # 61635 For replacement parts visit WENPRODUCTS.COM bit.ly/wenvideo IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions.
TABLE OF CONTENTS Product Specifications Safety Introduction Important Safety Rules Know Your Pneumatic Tool Know Your Attachments Mounting Attachments Connecting to Air Supply Operation Maintenance Troubleshooting Guide Exploded View & Parts List Warranty Statement 2 3 4 7 8 9 10 11 12 13 14 16 PRODUCT SPECIFICATIONS Model Number: 61635 Operating Pressure Range: 45 to 90 PSI (3 to 6.3 bar) Maximum Pressure: 91 PSI (6.
SAFETY INTRODUCTION Thanks for purchasing the WEN Pneumatic Spade. We know you are excited to put your tool to work, but first, please take a moment to read through the manual. This manual provides information regarding potential safety concerns, as well as helpful assembly and operating instructions. Safe operation of this tool requires that you read and understand this operator’s manual and all labels affixed to the tool. SAFETY ALERT SYMBOL: Indicates danger, warning, or caution.
IMPORTANT SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: To avoid mistakes and serious injury, do not use your tool until the following steps have been read and understood. LEARN the tool’s applications, limitations, and possible hazards. WORK AREA SAFETY 1. Keep your work area clean, uncluttered, and well lit.
IMPORTANT SAFETY RULES AIR SUPPLY SAFETY 1. Use only clean, dry, and regulated air. Condensation from an air compressor can rust and damage the internal workings of the tool. 2. DANGER OF EXPLOSION AND/OR SERIOUS PERSONAL INJURY. Do not use bottled gases to power this tool. Bottled compressed gases, including but not limited to oxygen, carbon dioxide, nitrogen, hydrogen, propane, acetylene or air are not for use with pneumatic tools.
IMPORTANT SAFETY RULES TOOL MAINTENANCE 1. Always disconnect the air supply before making adjustments or performing maintenance on the tool. 2. Do not alter or modify the tool in any way. Do not remove, tamper with, or otherwise cause the tool, trigger or safety bracket to become inoperable. Do not tape, tie, or otherwise fasten the trigger in the ON position. Do not remove springs from the safety bracket. Make daily inspections for free movement of the trigger and safety bracket. 3.
KNOW YOUR PNEUMATIC SPADE Carefully unpack the tool and accessories from the packaging. Check all components against the diagram and packing list below. If any part is damaged or missing, please contact our customer service department at (800) 232-1195, M-F 8-5 CST or email us at techsupport@wenproducts.com.
KNOW YOUR ATTACHMENTS Learn the recommended purposes of your attachments. All attachments have an 18 mm hex shank. Check the tool and all attachments to make sure they are free of damage before use. Accessory Name Flat Wide Chisel (Part No. 61635-027) 8 Appearance Recommended Purpose • Demolition work • Removing tiles • Removing plaster Flat Narrow Chisel (Part No. 61635-028) • Demolition work • Removing tiles • Removing plaster Pointed Chisel (Part No.
MOUNTING ATTACHMENTS WARNING: To prevent injury from accidental startups, the tool must be DISCONNECTED from the air supply before attaching or replacing accessories, or making any adjustments to the tool. WARNING: When handling sharp, pointed or hot attachments, always wear suitable protective gloves to avoid injuries. NOTE: Only use attachments that are designed for this tool. Replacement tools can be purchased from wenproducts.com by searching their part number, outlined on the previous page.
CONNECTING TO AIR SUPPLY Follow the instructions below to prepare the compressed air supply (not included). The working pressure of the air compressor MUST be regulated by a regulator to fit the operating pressure of your tool (45 to 90 PSI). NEVER let the air pressure exceed 91 PSI. The tool may be damaged if the maximum air pressure is exceeded. WARNING: Use only clean dry, and regulated air. Never use oxygen, combustible gases, bottled gases, or high pressure compressed gas to power this tool.
OPERATION WARNING: Serious or even fatal injuries can occur if the tool is pointed at persons or animals, even if there is no attachment installed in the tool. NEVER point the tool at people or animals. WARNING: User must wear proper eye and hearing protection when operating this tool. Stay alert and keep proper balance at all times. 1. Hold the tool with both hands and set the attachment against the work surface.
MAINTENANCE WARNING: To prevent accidental startup, always disconnect the tool from the air supply before carrying out any adjustments, service or maintenance. CLEANING Keep the tool free of dirt and dust. After each use, wipe the tool clean with a damp towel and some soft soap. Blow the tool clean using compressed air. Only use non-flammable cleaning solutions to wipe exterior of the tool if necessary. Do not soak tool with cleaning solutions. Such solutions can damage internal parts.
TROUBLESHOOTING GUIDE WARNING: Stop using the tool immediately if any of the following problems occur or risk serious personal injury. Repairs and replacements should only be performed by authorized personnel. If you have any questions, please contact our customer service at (800) 232-1195, M-F 8-5 CST. Problem Possible Causes Piston (Part No. 61635-021) is jammed/rusted in the housing due to a lack of lubrication oil Dirt has penetrated through the air hose. Tool does not start or lacks power.
EXPLODED VIEW & PARTS LIST 14
EXPLODED VIEW & PARTS LIST No. Part No.
LIMITED TWO YEAR WARRANTY WEN Products is committed to build tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.
