20-GAUGE 1/4-INCH CROWN STAPLER Model # 61702 bit.ly/wenvideo IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions. If you use your tool properly and for intended purpose, you will enjoy years of safe, reliable service.
TABLE OF CONTENTS Technical Data Safety Rules Know Your Stapler Operation Troubleshooting Exploded View Parts List Warranty 2 3 6 7 9 10 11 12 TECHNICAL DATA Model Number: Operating Pressure Range: Air Inlet: Staple Length: Staple Size: Crown: Staple Capacity: Air Consumption: Weight: 61702 70 psi - 100 psi 1/4˝ NPT 1/4˝ - 9/16˝ 20 Gauge 3/8˝ 100 0.28 SCFM 1.8 lbs Package Contents: One stapler, one S3 hex wrench, one S4 hex wrench, one oil bottle, one operator’s manual.
SAFETY RULES Hello! The purpose of the following safety symbols is to attract your attention to possible dangers. We don’t want any of our beloved customers accidentally injuring themselves. The safety symbols and the explanations with them deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. These instructions and warnings are not substitutes for proper accident prevention measures (obviously).
SAFETY RULES 7. DRESS FOR SAFETY. Do not wear loose clothing, gloves, neckties, or jewelry (rings, watches, etc.) when operating the tool. Inappropriate clothing and items can get caught in moving parts and draw you in. ALWAYS wear non-slip footwear and tie back long hair. 8. WEAR A FACE MASK OR DUST MASK to fight the debris produced by operation and ear protection to fight hearing loss. Everyone in the work area MUST wear safety glasses with side shields. These safety glasses must conform to ANSI Z87.
SAFETY RULES 18. MAKE THE WORKSHOP CHILDPROOF. Use padlocks and master switches and ALWAYS remove starter keys. Keep bystanders, children and visitors away while operating the power tool. Distractions can cause you to lose control. When tool is not in use, it should be locked away in a safe place. 19. DO NOT operate the tool if you are under the influence of drugs, alcohol, or medication that may affect your ability to properly use the tool. 20. REMOVE FINGER FROM TRIGGER when not driving fasteners.
SAFETY RULES 31. KEEP ALERT. Watch what you are doing. Use common sense. Do not operate any tool when you are tired. 32. USE PROPER EXTENSION CORDS. When using an air compressor outdoors, use only rounded jackets extensions cords. These are intended for outside use. See manufacturer’s manual for the AWG required for the compressor’s amperage draw. 33. PAY ATTENTION TO AIR HOSE AND THEIR CONNECTIONS. Don’t trip over the hoses. It isn’t fun. Also, make sure the connections are nice and tight. 34.
OPERATION WARNING - if any parts are missing, do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. LUBRICATION This tool requires lubrication before each use (especially the first use). If an in-line oiler is used, manual lubrication through the air inlet is not required. Note: the work surface can become damaged by excessive lubrication. Proper lubrication is the owner’s responsibility.
OPERATION LOADING THE STAPLE Warning: TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION, BEFORE LOADING: • Wear ANSI-approved safety goggles with side shields. Other people in the work area must also wear ANSI-approved impact safety goggles with side shields. • Release the trigger. • Detach the air supply. • Attempt to fire the tool into a piece of scrap wood to ensure that it is incapable of firing any fasteners. 1. Only use the proper size and type of staple with this stapler. 2.
OPERATION CLEARING A JAMMED STAPLE WARNING: Disconnect the air line from the stapler and remove staples from the magazine before making adjustments or personal injury may result. 1. If a staple is jammed in the discharge area, remove it with pliers. 2. If a staple is jammed in the magazine, pull the magazine unit all the way back to the engaged position. Use a screwdriver to release the jammed fastener by probing the openings in the magazine. 3.
EXPLODED VIEW 10
PARTS LIST Item 1 2 2a 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Stock # 61702-001 61702-002 61702-002a 61702-003 61702-004 61702-005 61702-006 61702-007 61702-008 61702-009 61702-010 61702-011 61702-012 61702-013 61702-014 61702-015 61702-016 61702-017 61702-018 61702-019 61702-020 61702-021 61702-022 61702-023 61702-024 61702-025 61702-026 61702-027 61702-028 61702-029 Description SCREW CYLINDER CAP EXHAUST DEFLECTOR GASKET SEAL O-RING 15.7×2 SPRING O-RING 31.3×2.
LIMITED ONE YEAR WARRANTY WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of one (1) year from date of purchase.
