MODEL 61705 20-GAUGE 3/8-INCH CROWN STAPLER For replacement parts visit WENPRODUCTS.COM IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions.
TABLE OF CONTENTS Specifications.......................................................................................2 Introduction.........................................................................................3 General Safety Rules............................................................................4 Specific Rules for the Stapler...............................................................6 Know Your Stapler..............................................................................
INTRODUCTION Thanks for purchasing the WEN crown stapler. We know you are excited to put your tool to work, but first, please take a moment to read through the manual. Safe operation of this tool requires that you read and understand this operator’s manual and all the labels affixed to the tool. This manual provides information regarding potential safety concerns, as well as helpful assembly and operating instructions for your tool. WARNING: Indicates danger, warning, or caution.
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert, and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: Read and understand all warnings, cautions and operating instructions before using this tool. Failure to follow all instructions listed below may result in personal injury and tool damage. WORK AREA SAFETY 1. Keep work area clean and well lit. Cluttered or dark areas invite accidents. 2.
GENERAL SAFETY RULES 4. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents. 5. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. 6. Do not overreach.
SPECIFIC RULES FOR STAPLERS WARNING: To avoid mistakes and serious injury, do not use your tool until the following steps have been read and understood. 1. AIR PRESSURE • Use air pressure that is compatible with the ratings on the nameplate of the tool. • Air pressure should not exceed 100 psi or 6.9 bar. • Do not connect the tool to a compressor rated at over 175 psi even in the event of a regulator failure. • Use only clean, dry, and regulated air.
SPECIFIC RULES FOR STAPLERS 10. DO NOT REMOVE, tamper with, or otherwise cause the tool or trigger to become inoperable. Do not tape or tie the trigger in the ON position. Make daily inspections for free movement of the trigger. Uncontrolled discharge may result. Do not alter or modify the tool in any way. 11. DO NOT OVERREACH. Keep proper footing and balance at all times. Wear oil-resistant rubber-soled footwear. Keep the floor clear of oil, scrap, and other debris. 12. MAINTAIN TOOLS PROPERLY.
KNOW YOUR STAPLER Exhaust Cover Air Inlet Magazine Lock Magazine Trigger PACKING LIST Check your packing list against the diagram below. If any part is damaged or missing, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email us at techsupport@wenproducts.com. 2 1 3 1. 2. 3. 4.
OPERATION LUBRICATION This tool requires lubrication before each use (especially the first use). If an in-line oiler is used, manual lubrication through the air inlet is not required. NOTE: the work surface can become damaged by excessive lubrication. Proper lubrication is the owner’s responsibility. Failure to lubricate the tool properly will drastically shorten the life of the tool and void the warranty. 1. Disconnect the air supply from the tool to add lubricant. 2.
OPERATION LOADING THE STAPLER (FIG. 3) WARNING: TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION, BEFORE LOADING: • You and other people in the work area must wear ANSI-approved safety goggles with side shields. • Release the trigger. • Connect the tool to a compressed air source. • Attempt to fire the tool into a piece of scrap wood to ensure that it is incapable of firing any fasteners. 1. Only use the proper size and type of staple with this stapler. Refer to the specifications table on p.
OPERATION AFTER USE, TO PREVENT ACCIDENTS: 1. Release the trigger. 2. Detach the air supply. 3. Attempt to fire the tool into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any fasteners. 4. Release the trigger again. 5. Clean external surfaces with clean, dry cloth. 6. Store indoors and out of reach of children and unauthorized people.
11 10 9 8 7 6 5 4 3 2 1 2a 16 17 15 14 13 12 30 34 31 29 32 33 27 26 24 22 20 18 28 25 23 47 19 50 49 21 35 27 54 36 46 48 55 45 51 53 52 37 38 56 57 39 40 44 43 41 42 EXPLODED VIEW & PARTS LIST
EXPLODED VIEW & PARTS LIST NO. MODEL 1 61702-001 2 DESCRIPTION NO. MODEL DESCRIPTION Screw 30 61702-030 Screw 61705-002 Cylinder Cap 31 61702-031 Plate 2a 61702-002a Exhaust Deflector 32 61702-032 Screw 3 61702-003 Gasket 33 61702-033 Drive Guide 4 61702-004 Seal 34 61702-034 Spring Pin 2 x 10 5 61702-005 O-Ring 15.7 x 2 35 61702-035 Fixed Magazine Unit 6 61702-006 Spring 36 61702-036 Screw 7 61702-007 O-Ring 31.3 x 2.
WARRANTY STATEMENT WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship during personal use for a period of two (2) years used for professional or commercial use.
NOTES 15
THANKS FOR REMEMBERING V. 2020.06.
