8-GAUGE NARROW CROWN STAPLER Model # 61710 IMPORTANT: bit.ly/wenvideo Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions. If you use your tool properly and for intended purpose, you will enjoy years of safe, reliable service.
TABLE OF CONTENTS Technical Data General Safety Rules Specific Safety Rules Know Your Nailer Operation Maintenance Troubleshooting Exploded View Parts List Warranty 2 3 4 7 7 9 10 11 12 13 TECHNICAL DATA Model Number: Operating Pressure Range: Air Inlet: Nail Size Range: Nail Diameter: Magazine Capacity: Weight: Package Contents: 2 61710 60 psi - 100 psi 1/4˝ NPT 3/8 to 1 inch 18-Gauge 100 2.
GENERAL SAFETY RULES Hello! The purpose of the following safety symbols is to attract your attention to possible dangers. We don’t want any of our beloved WEN customers accidentally injuring themselves. The safety symbols and the explanations with them deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. These instructions and warnings are not substitutes for proper accident prevention measures (obviously).
SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: To avoid mistakes and serious injury, do not use your tool until the following steps have been read and understood 1. READ and become familiar with this entire instruction manual, no matter how boring it may be. LEARN the tool’s applications, limitations, and possible hazards. 2. REGULATE AIR PRESSURE.
SAFETY RULES 12. DISCONNECT tool from air supply when not in use. Remove fasteners from magazine before leaving the area or passing the tool to another operator. Do not climb ladders, stairs, scaffoldings, etc. without disconnecting the tool. Do not carry a connected tool to another work area. Do not make adjustments, remove magazine, perform maintenance or clear jammed fasteners while connected to the air supply.
SAFETY RULES of an angle. Personal injury from strong recoil, jammed fasteners, or richocheted nails may result. 25. BE AWARE of material thickness when using the nailer. A protruding nail may cause injury. 26. KNOW that when the tool is being utilized at pressures on the high end of its oeprating range, nails can be driven completely through thin or very soft work material. Make sure the pressure in the compressor is set so that nails are set into the material and not pushed completely through. 27.
KNOW YOUR NAILER 1- Jam-Clearing Latch 2- Contact Trip 3- Magazine 4- Air Inlet 5- Trigger 6- Exhaust OPERATION WARNING - if any parts are missing, do not operate this tool until the missing parts are replaced. Failure to do so could result in a possibly serious personal injury. LUBRICATION This tool requires lubrication before each use (especially the first use). If an inline oiler is used, manual lubrication through the air inlet is not required.
OPERATION LOADING THE FASTENERS CAUTION: Always disconnect the tool from the air supply before loading fasteners. 1. Press the lock to release the movable magazine and pull the magazine out fully. 2. Place a full clip of the specified type and size fasteners on the fixed magazine, up to 100 fasteners may be loaded in the magazine. 3. Push the movable magazine forward until it was locked.
OPERATION CLEARING JAMMED NAILS WARNING: Failure to disconnect air line from the tool and remove all fasteners before removing jammed nails to avoid personal injury. If a nail becomes jammed in the nosepiece, keep the tool pointed away from yourself and others and follow these steps: 1. Disconnect air supply from tool. 2. Press magazine lock to release movable magazine. 3. Push down jam clearing latch and pull up to open front plate. 4. Remove jammed nail, using pliers or other tools if necessary. 5.
TROUBLESHOOTING CAUTION: Stop using the tool immediately if any of the following problems occur or risk serious personal injury. Repairs and replacements should only be performed by authorized personnel at a certified WEN service center. Problem Air leaking at Trigger area Solution 1. Check and replace O-ring. 2. Check and replace trigger valve head. 3. Check and replace trigger valve stem, seal or O-ring.
EXPLODED VIEW 11
PARTS LIST 12 Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Stock # 61710-001 61710-002 61710-003 61710-004 61710-005 61710-006 61710-007 61710-008 61710-009 61710-010 61710-011 61710-012 61710-013 61710-014 61710-015 61710-016 61710-017 61710-018 61710-019 61710-020 61710-021 61710-022 61710-023 61710-024 61710-025 61710-026 61710-027 61710-028 61710-029 61710-030 61710-031 61710-032 61710-033 61710-034 Description SCREW BUSHING EXHAUST COVER SE
LIMITED ONE YEAR WARRANTY WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of one (1) year from date of purchase.
