Table of Contents Technical Data…………………………………………………………… 2 General Safety Rules……………………………………………………… 3 Specific Safety Rules for Stapler………………………………………... 6 Know Your Stapler………………………………………………………. 8 Operation………………………………………………………………... 9 Troubleshooting……………………………………………………….. 12 Exploded View………………………………………………………….. 13 Parts List…………………………………………………………………. 14 Warranty………………………………………………………………… 15 Technical Data Operating pressure range 60 psi-100 psi Air inlet 1/4" NPT Air consumption 1.
General Safety Rules The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. Symbol Meaning Safety Alert Symbol: Indicated danger, warning, or caution, may be used in conjunction with other symbols or pictographs.
Only use air hose that is rated for a maximum working pressure of at least 150 psi (10.3 BAR) or 150% of the maximum system pressure, which ever is greater. Do not use bottled gases to power this tool. Bottled compressed gases such as oxygen, carbon dioxide, nitrogen, hydrogen, propane, acetylene or air are not for use with pneumatic tools. Never use combustible gases or any other reactive gas as a power source for this tool.
Refer to the Maintenance and Repairs for detailed information on the proper maintenance of the tool. Always operate the tool in a clean, lighted area. Be sure the work surface is clear of any debris and be careful not to lose footing when working in elevated environments such as rooftops. Do not drive fasteners near edge of material. The workpiece may split causing the fastener to ricochet, injuring you or a co-worker.
Specific Safety Rules for Stapler 1. KEEP WORKING AREA CLEAN. Cluttered areas invite injuries. 2. DON’T ALLOW CHILDREN KEEP AT THE WORKING AREA. Don’t let them handle the tool. 3. DO NOT OPERATE THIS TOOL IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read warning label on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not attempt to operate. 4. USE SAFETY GLASSES. Safety glasses should conform to ANSI Z87.1 specifications.
17. USE THE CORRECT AIR CONNECTOR. The connector on the tool must not hold pressure when the air supply is disconnected. If the wrong fitting is used, the tool can be charged with air after being disconnected and still be able to drive a fastener. 18. WHEN CONNECTING THE AIR. The tool can possibly fire the fasteners. Therefore, remove all the fasteners before connecting to the air. 19. DO NOT DEPRESS THE SAFE BRACKET AND THE TRIGGER WHEN LOADING. 20. IF THE FASTENERS ARE JAMMED.
Know Your Stapler 1-Jam Clearing Latch 2-Contact Trip 3-Magazine 4-Air Inlet 5-Trigger 6-Exhaust 8
Operation WARNING - if any parts are missing, do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. Lubrication This tool requires lubrication before using the tool for the first time and before each use. If an inline oiler is used, manual lubrication through the air inlet is not required. Note: The work surface can become damaged by excessive lubrication. Proper lubrication is the owner’s responsibility.
Loading the fasteners Caution: Always disconnect the tool from the air supply before loading the fasteners. 1. Depress the lock to release the movable magazine and pull the magazine out fully. 2. Place a full clip of the specified type and size fasteners on the fixed magazine, up to 100 fasteners may be loaded in the magazine. 3. Push the movable magazine forward until it was locked.
Clearing a jammed nail Warning: Disconnect air line from tool and remove fasteners from magazine before making adjustments or personal injury may result. If a nail becomes jammed in the nosepiece, keep the tool pointed away from you and follow these instructions to clear: 1. Disconnect air supply from tool. 2. Press magazine lock to release movable magazine. 3. Push down jam clearing latch then pull up to open front plate. 4. Remove jammed nail, using pliers if necessary. 5.
Troubleshooting Caution: Stop using the tool immediately if any of the following problems occur. Serious personal injury could occur. Any repairs or replacements must be done by a qualified person or an authorized WEN® service center only.
Exploded View 13
Parts List Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Stock # 61710-001 61710-002 61710-003 61710-004 61710-005 61710-006 61710-007 61710-008 61710-009 61710-010 61710-011 61710-012 61710-013 61710-014 61710-015 61710-016 61710-017 61710-018 61710-019 61710-020 61710-021 61710-022 61710-023 61710-024 61710-025 61710-026 61710-027 61710-028 61710-029 61710-030 61710-031 61710-032 61710-033 61710-034 Description Item 35 36 37 38 39 40 41 42 43 44 45 46
Limited One Year Warranty WEN Products is committed to build tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC ("Seller") warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of one (1) year from date of purchase.