PNEUMATIC 2-IN-1 NAILER Model # 61718 For replacement parts visit WENPRODUCTS.COM bit.ly/wenvideo IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions.
TABLE OF CONTENTS 2 3 4 7 8 10 12 13 14 16 Technical Data Safety Introduction Important Safety Rules Know Your Nailer Preparation and Adjustments Operation Maintenance Troubleshooting Guide Exploded View and Parts List Warranty Statement TECHNICAL DATA Model Number: Minimum Operating Pressure: Maximum Operating Pressure: Air Inlet: Air Consumption per Fastener: Nail Type: Nail Length: Staple Type: Staple Length: Magazine Capacity: Weight: 2 61718 60 PSI 100 PSI 1/4˝- 18 NPT 0.
SAFETY INTRODUCTION Thanks for purchasing the WEN 2-in-1 Nailer & Stapler. This tool is designed for household use only, not for industrial or professional purposes. Safe operation of this pneumatic tool requires that you read and understand this instruction manual and all labels affixed to the tool. Safety is a combination of common sense, staying alert, and knowing how your tool works. SAFETY ALERT SYMBOL: Indicates danger, warning, or caution.
IMPORTANT SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: To avoid mistakes and serious injury, do not use your tool until the following steps have been read and understood. LEARN the tool’s applications, limitations, and possible hazards. WORK AREA SAFETY 1. KEEP YOUR WORK AREA clean, uncluttered, and well lit. Do not work on floor surfaces that are slippery with sawdust or wax.
IMPORTANT SAFETY RULES AIR SUPPLY SAFETY 1. USE ONLY CLEAN, DRY, AND REGULATED AIR. Condensation from an air compressor can rust and damage the internal workings of the tool. Regularly drain water and contaminants out from the compressor. An inline filter is recommended to remove most of these contaminants and prolong the life of the tool the compressor. 2. DANGER OF EXPLOSION AND/OR SERIOUS PERSONAL INJURY. Do not use bottled gases to power this tool.
IMPORTANT SAFETY RULES TOOL SAFETY 1. THIS TOOL IS DESIGNED for household use only, not for industrial or professional purposes. Do not force the tool to do a job for which it was not designed. 2. INSPECT TOOL BEFORE USE. Do not operate if any portion of the tool, trigger, or safety bracket is damaged, inoperable, disconnected, or altered. Leaking air, damaged parts, or missing parts should be repaired or replaced. 3.
KNOW YOUR NAILER Carefully unpack the tool from the packaging. Check all components and compare against the graph below. If any part is damaged or missing, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email us at techsupport@wenproducts.com.
PREPARATION AND ADJUSTMENTS LUBRICATING THE TOOL (Fig. 1) This tool requires lubrication before each use (especially the first use). Proper lubrication is the owner’s responsibility. Failure to lubricate the tool properly will dramatically shorten the life of the tool and void the warranty. NOTE: The in-line oiler is a convenient way to provide oil to the tool. If an in-line oiler is installed, manual lubrication through the air inlet is not required. Oil 1.
PREPARATION AND ADJUSTMENTS LOADING THE FASTENERS (Figs. 3 to 6) WARNING: Always load the fasteners after connecting the tool to its air supply. Otherwise, unwanted misfires may occur during connection. Never aim the tip towards yourself or others. 1. Depress the magazine lock and pull out the movable magazine fully (Fig 3). Fig. 3 2. Hold the nailer with the magazine to your side. Make sure the firing tip is directed away from yourself or others. 3.
OPERATION WARNING: Before each use, check the nailer, compressed air connections and air lines. If any parts are missing or damaged, do not operate this tool until the parts are repaired and replaced. Failure to do so could possibly result in a serious personal injury. ADJUSTING THE DEPTH ADJUSTMENT WHEEL (Fig. 8) The nailer is equipped with a depth adjustment wheel (Fig. 8) for setting the penetration depth of the fasteners. 1. Turn the wheel clockwise to increase the firing depth (wheel moves downwards).
OPERATION DRIVING MODE This nailer follows a single driving mode, which means only one fastener will be driven at a time. There is no bumpfire mode for this nailer. This type of driving mode minimizes the chances of accidental firing and maximizes safety. The nailer is equipped with a safety bracket that needs to be activated before pulling the trigger in order to drive a fastener. The driving process can only be triggered in the following sequence of activation: 1.
MAINTENANCE WARNING: Disconnect tool from air supply and empty fasteners from the magazine before performing any cleaning or maintenance. LUBRICATION Routine lubrication of the tool is required for best performance. If tool is used without an in-line oiler, place 3 to 4 drops of pneumatic tool oil into the air inlet of the tool at the beginning of each workday. This will ensure the moving components are finely lubricated. CLEANING Keep tools clean for better and safer performance.
TROUBLE SHOOTING WARNING: Stop using the tool immediately if any of the following problems occur or risk serious personal injury. Repairs and replacements should only be performed by authorized personnel. If you have any questions, please contact our customer service at (800) 232-1195, M-F 8-5 CST. Problem Air leaking at trigger area Common Causes 1. O-ring in trigger valve is damaged. 2. Trigger valve head is damaged. 3. Trigger valve stem, seal or O-ring is damaged.
EXPLODED VIEW AND PARTS LIST 14
EXPLODED VIEW AND PARTS LIST No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 Parts No.
LIMITED TWO YEAR WARRANTY WEN Products is committed to build tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.
