4-IN-1 PNEUMATIC FLOORING NAILER For replacement parts visit Model # 61741 bit.ly/wenvideo WENPRODUCTS.COM IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions.
TABLE OF CONTENTS 2 4 7 7 9 11 12 14 15 Technical Data Safety Rules Get to Know Your Air Nailer Assembly Operation Troubleshooting Exploded View and Parts List Maintenance Warranty TECHNICAL DATA Model Number: Minimum Operating Air Pressure: Maximum Operating Air Pressure: Nail Size: Nail Length Range: Staple Size: Staple Length Range: Magazine Capacity: Air Inlet: Air Consumption: Tool Weight: 2 WEN 61741 60 PSI 100 PSI 18 Gauge 5/8 to 2 in. 1/4 in. Crown 1/2 to 1-5/8 in. 100 nails/staples 1/4 in.
GENERAL SAFETY RULES Hello! The purpose of the following safety symbols is to attract your attention to possible dangers. We don’t want any of our beloved WEN customers accidentally injuring themselves. The safety symbols and the explanations with them deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. These instructions and warnings are not substitutes for proper accident prevention measures.
SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: To avoid mistakes and serious injury, do not use your tool until the following steps have been read and understood 1. READ and become familiar with this entire instruction manual, no matter how boring it may be. LEARN the tool’s applications, limitations, and possible hazards. 2. REGULATE AIR PRESSURE.
SAFETY RULES magazine, perform maintenance or clear jammed fasteners while connected to the air supply. If the contact trip is adjusted when the tool is connected to the air supply with loaded nails, accidental discharge may occur. 13. LOAD FASTENERS after connecting the tool to the air supply. Otherwise, fasteners are at risk of being fired during connection. The tool’s driving mechanism may cycle when it is connected to the air supply.
SAFETY RULES 26. KNOW that when the tool is being utilized at pressures on the high end of its operating range, nails can be driven completely through thin or very soft work material. Make sure the pressure in the compressor is set so that nails are set into the material and not pushed completely through. 27. KEEP HANDS AND BODY PARTS CLEAR of immediate work area. Hold workpiece with clamps when necessary to keep body parts out of potential harm.
GET TO KNOW YOUR AIR NAILER Magazine Lock Air Inlet Movable Magazine Trigger Air Exhaust Fixed Magazine D-Ring Pin Depth Adjustment Wheel Plate Pressing Latch Shoe Adjustment Knob Nosepiece Flooring Shoe Contact Tip ASSEMBLY UNPACKING Be sure to remove all loose parts from the packaging. Refer to the table to the right and check all the parts are complete. If you find any pieces that are missing or wrong, please contact our customer service.
ASSEMBLY LUBRICATION This tool requires lubrication before each use (especially the first use). If an inline oiler is used, manual lubrication through the air inlet is not required. 1 Note: The work surface can become damaged by excessive lubrication. Proper lubrication is the owner’s responsibility. Failure to lubricate the tool properly will dramatically shorten the life of the tool and void the warranty. Fig. 2 1. Disconnect the air supply from the tool to add lubricant. 2.
OPERATION Test the driving depth in a sample piece of wood before using. If the fasteners are being driven too far or not far enough, adjust the regulator to provide less air pressure or more air pressure. 1. Check that the air supply is correctly connected to the tool at the correct pressure and the fasteners have been loaded into the magazine. 2. Hold the nailer and press the drive guide (Fig. 5 - 1) flush against the work surface, making sure that the tool is straight. Gently press the trigger (Fig.
OPERATION WARNING: Never uninstall or install the flooring shoe while the nailer/stapler is attached to its air supply or while nails are loaded in the magazine. B A REMOVING THE FLOORING SHOE For general installation at a 90-degree angle, use the following directions to uninstall the flooring shoe. 1. Open the plate pressing latch (Fig. 6). Fig. 6 Fig. 7 Fig. 8 Fig. 9 2. Open the D-ring pin by unclasping the hook (Fig. 7 - A) from the pin. 3. Remove the pin from the floor shoe (Fig. 7 - B). 4.
OPERATION FINISHING APPLICATIONS In order to prevent marring and damage to the surface of your work piece, attach the no-mar tip (Fig. 13) before attempting any finish nailing. To attach the no-mar tip, slide the tip onto the drive guide (Fig. 14). Note: The no-mar tip is only to be used for the purpose of finishing applications. Do not use for flooring applications. Fig. 14 Fig. 13 TROUBLESHOOTING Stop using the tool immediately if any of the following problems occur.
EXPLODED VIEW AND PARTS LIST 12
EXPLODED VIEW AND PARTS LIST No.
MAINTENANCE WARNING: Remove nails from magazine and disconnect the air supply before performing any maintenance. Routine lubrication of the tool is required for best performance. Oil added through the airline connection will lubricate internal parts. An automatic airline oilier is recommended but oil may be added manually before every operation or after about 1 hour of continuous use. Only a few drops of oil at a time are necessary.
LIMITED TWO YEAR WARRANTY WEN Products is committed to build tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.
THANKS FOR REMEMBERING
