COIL ROOFING NAILER Model # 61782 bit.ly/wenvideo IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions. If you use your tool properly and for intended purpose, you will enjoy years of safe, reliable service.
TABLE OF CONTENTS Technical Data Fastener Specifications Safety Rules Know Your Nailer Operation Exploded View and Parts List Maintenance Troubleshooting Warranty 2 3 3 7 7 10 12 12 13 TECHNICAL DATA Model Number: Operating Pressure Range: Air Inlet: Fastener Length: Fastener Diameter: Air Consumption: Magazine Capacity: Weight: Package Contents: 2 61782 70 psi - 120 psi 1/4˝ NPT 3/4˝ - 1-3/4˝ 0.120˝ (11 gauge) 0.1 cube feet/ cycle at 100 psi 120 5.
FASTENERS SPECIFICATIONS Only use recommended fasteners (screw, ring or smooth shank). SAFETY RULES Hello! The purpose of the following safety symbols is to attract your attention to possible dangers. We don’t want any of our beloved customers accidentally injuring themselves. The safety symbols and the explanations with them deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger.
SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: To avoid mistakes and serious injury, do not use your tool until the following steps have been read and understood 1. READ and become familiar with this entire instruction manual, no matter how boring it may be. LEARN the tool’s applications, limitations, and possible hazards. 2. REGULATE AIR PRESSURE.
SAFETY RULES 12. DISCONNECT tool from air supply when not in use. Remove fasteners from magazine before leaving the area or passing the tool to another operator. Do not climb ladders, stairs, scaffoldings, etc. without disconnecting the tool. Do not carry a connected tool to another work area. Do not make adjustments, remove magazine, perform maintenance or clear jammed fasteners while connected to the air supply.
SAFETY RULES 24. DO NOT DRIVE NAILS onto the heads of other fasteners. Do not use the tool at too steep of an angle. Personal injury from strong recoil, jammed fasteners, or ricochetted nails may result. 25. BE AWARE of material thickness when using the nailer. A protruding nail may cause injury. 26. KNOW that when the tool is being utilized at pressures on the high end of its operating range, nails can be driven completely through thin or very soft work material.
KNOW YOUR NAILER Exhaust Cover Depth Setting Wheel Trigger Safety Bracket Air Inlet Shingle Guide Magazine OPERATION WARNING - if any parts are missing, do not operate this tool until the missing parts are replaced. Failure to do so could result in a possibly serious personal injury. LUBRICATION (FIG. A) This tool requires lubrication before each use (especially the first use). If an inline oiler is used, manual lubrication through the air inlet is not required.
OPERATION LOADING THE FASTENERS (FIG. C to E) 1. Open the magazine. Pull down door latch and swing door open. Door swing to the left. Swing magazine cover open. Magazine cover swings to the right. 2. Check the adjustment for the size of nail to be inserted. The nail support can be moved up or down to three settings. To change the setting, pull up on the post and twist to the correct stop.
OPERATION TO CHANGE THE TRIGGER (FIG. H) WARNING: Disconnect air line from tool and remove fasteners from magazine before making adjustments or personal injury may result. To swap out the trigger switch: 1. Remove the o-ring on the side of the trigger pin. 2. Remove the trigger pin, the trigger and the trigger spring. 3. Swap the trigger switch out for the alternative trigger. 4. Replace the trigger spring, the trigger, the trigger pin and the o-ring. Fig.
EXPLODED VIEW AND PARTS LIST 10 No. Part No. Description No. Part No. Description No. Part No. Description 1 61782B-001 Screw M5x20 36 61782B-036 Adjuster 71 61782B-071 Pin 2 61782B-002 Bushing 37 61782B-037 Bracket Assembly 72 61782B-072 O ring 24.3x2.
EXPLODED VIEW AND PARTS LIST 11
MAINTENANCE CAUTION - Disconnect tool from air before cleaning and inspections. Correct all problems before operation. Add pneumatic tool oil into the oiler regularly to ensure the moving components are finely lubricated. Check the filter of the compressor weekly and switch off the manual valve to drain water and contaminations out. Wipe the tool clean. Blow the tool clean using high compressed air, then use non-flammable cleaning solutions to wipe exterior of the tool as necessary.
LIMITED ONE YEAR WARRANTY WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of one (1) year from date of purchase.
