Table of Contents Technical Data…………………………………………………………… 2 Fastener Specifications…………………………………………………… 3 General Safety Rules……………………………………………………… 4 Specific Safety Rules for Coil Roofing Nailer…………………………... 7 Know Your Nailer……………………………………………………….. 9 Operation………………………………………………………………... 10 Troubleshooting………………………………………………………….. 13 Exploded View………………………………………………………….. 15 Parts List………………………………………………………………….
Fastener Specifications Only use recommended fasteners. They may be screw, ring and smooth shank.
General Safety Rules The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. Symbol Meaning Safety Alert Symbol: Indicated danger, warning, or caution, may be used in conjunction with other symbols or pictographs.
General Safety Rules (Continued) • • • • • • • • • • • • • • • Only use air hose that is rated for a maximum working pressure of at least 150 psi (10.3 BAR) or 150% of the maximum system pressure, which ever is greater. Do not use bottled gases to power this tool. Bottled compressed gases such as oxygen, carbon dioxide, nitrogen, hydrogen, propane, acetylene or air are not for use with pneumatic tools. Never use combustible gases or any other reactive gas as a power source for this tool.
General Safety Rules (Continued) • • • • • • • • • • • Do not use the body of the tool or top cap as a hammer. Discharged fasteners may follow unexpected path and cause injury. Always keep fingers clear of contact trip to prevent injury from inadvertent release of nails. Refer to the Maintenance and Repairs for detailed information on the proper maintenance of the tool. Always operate the tool in a clean, lighted area.
Specific Safety Rules for Coil Roofing Nailer 1. KEEP WORKING AREA CLEAN. Cluttered areas invite injuries. 2. DON’T ALLOW CHILDREN KEEP AT THE WORKING AREA. Don’t let them handle the tool. 3. DO NOT OPERATE THIS TOOL IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read warning label on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not attempt to operate. 4. USE SAFETY GLASSES. Safety glasses should conform to ANSI Z87.1 specifications.
Specific Safety Rules for Coil Roofing Nailer (Continued) 17. USE THE CORRECT AIR CONNECTOR. The connector on the tool must not hold pressure when the air supply is disconnected. If the wrong fitting is used, the tool can be charged with air after being disconnected and still be able to drive a fastener. 18. WHEN CONNECTING THE AIR. The tool can possibly fire the fasteners. Therefore, remove all the fasteners before connecting to the air. 19. DO NOT DEPRESS THE SAFE BRACKET AND THE TRIGGER WHEN LOADING.
Know Your Nailer 1 2 3 4 7 5 6 1-Adjustable Exhaust Deflector 2-Air Inlet 3-Trigger 4-Magazine 5-Shingle Guide 6-Contact Trip 7-Depth Setting Wheel 9
Operation WARNING - if any parts are missing, do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. Lubrication This tool requires lubrication before using the tool for the first time and before each use. If an inline oiler is used, manual lubrication through the air inlet is not required. Note: The work surface can become damaged by excessive lubrication. Proper lubrication is the owner’s responsibility.
Operation (Continued) Loading the fasteners Caution: Always disconnect the tool from the air supply before loading the fasteners. 1. Open the magazine. Pull down door latch and swing door open. Door swing to the left. Swing magazine cover open. Magazine cover swings to the right. 2. Check the adjustment for the size of nail to be inserted. The nail support can be moved up or down to three settings. To change the setting, pull up on the post and twist to the correct stop.
Operation (Continued) Actuating tool Warning: To reduce the risk of injury, Always wear proper eye and hearing protection when operating this tool. Warning: A nail will fire each time the trigger is depressed as long as the contact trip remains depressed which could result in inadvertent actuation. 1. Depress the contact trip firmly against the work surface. 2. Depress the trigger.
Troubleshooting Caution: Stop using the tool immediately if any of the following problems occur. Serious personal injury could occur. Problem Air leaking at Trigger area Cause 1. O-ring in trigger valve stem is worn and damaged. 2. O-ring in trigger valve head is worn and damaged. 3. Foreign matter is preventing the trigger from moving to OFF position. Solution 1. Check/replace O-ring/lubricate. 2. Check/replace O-ring/lubricate. 3. Clean the tool/lubricate. Air leaking at the body.
Troubleshooting (Continued) Problem Skipping fasteners/feeding intermittently Runs slowly or has power loss Cause 1. Foreign matter lodged between the small piston and small cylinder. 2. O-ring on the small piston is worn and damaged. 3. Tool dry and lack lubrication. 4. The spring on the small piston is damaged. 5. Air pressure is too low. 6. Connecting screw of nose and body is loose. 7. Stopped hook (87) can't stop the fasteners. 8. Bent fasteners. 9. Wrong size fasteners. 10. Gasket is damaged. 11.
Exploded View 15
Parts List Item# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 22a 22b 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 44a 45 Stock # 61782-001 61782-002 61782-003 61782-004 61782-005 61782-006 61782-007 61782-008 61782-009 61782-010 61782-011 61782-012 61782-013 61782-014 61782-015 61782-016 61782-017 61782-018 61782-019 61782-020 61782-021 61782-022 61782-022a 61782-022b 61782-023 61782-024 61782-025 61782-026 61782-027 61782-028 61782-029 61782-030 61782-031 61782-032 61782-
Limited One Year Warranty WEN Products is committed to build tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC ("Seller") warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of one (1) year from date of purchase.
