/3 Sheet Sander Model # 6313 bit.ly/wenvideo IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for easy operation, dependability and maximum user safety. When properly cared for, this product will supply rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings and cautions. If you use your tool properly and for its intended purpose, you will enjoy years of safe, reliable service.
TABLE OF CONTENTS 2 3 4 6 7 7 9 10 11 13 Technical Data General Safety Rules Specific Safety Rules For The Sander Electrical Information Know Your Sander Operating Instruction Maintenance Troubleshooting Exploded View and Parts List Warranty TECHNICAL DATA Model Number: Motor: Speed: Cord length: Size of sandpaper: Weight: Includes: 2 6313 120 V, 60 Hz, 1.2 A 12,000 RPM (no load) 6 feet 1/3 sheet 3.
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: To avoid mistakes and serious injury, do not plug in your tool until the following steps have been read and understood. 1. READ and become familiar with this entire instruction manual. LEARN the tool’s applications, limitations, and possible hazards. 2. AVOID DANGEROUS CONDITIONS. Do not use power tools in wet or damp areas or expose them to rain.
GENERAL SAFETY RULES 14. NEVER STAND ON A TOOL. Serious injury could result if the tool tips or is accidentally hit. DO NOT store anything above or near the tool. 15. DO NOT OVERREACH. Keep proper footing and balance at all times. Wear oil-resistant rubber-soled footwear. Keep the floor clear of oil, scrap, and other debris. 16. MAINTAIN TOOLS PROPERLY. ALWAYS keep tools clean and in good working order. Follow instructions for lubricating and changing accessories. 17. CHECK FOR DAMAGED PARTS.
SPECIFIC RULES FOR THE SANDER 6. If the power cord is damaged, it must be replaced only by the manufacturer or by an authorized service center. 7. Save these instructions. Refer to them frequently and use them to instruct others who may use this product. If you loan someone this product, loan them these instructions also. 8. Do not use the sander to remove lead-based paints.
ELECTRICAL INFORMATION DOUBLE INSULATION Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded. WARNING: The double insulated system is intended to protect the user from shock resulting from a break in the tool’s internal insulation.
KNOW YOUR SANDER Switch Dust collection bag Sanding base OPERATING INSTRUCTIONS TOOL SET UP WARNING: To avoid injury from accidental startups, turn switch OFF and remove the plug from the power source outlet before making any adjustments. INSTALLING NON-HOOK AND LOOP SANDPAPER 1. Unplug the sander. 2. Inspect the sandpaper before installing; do not use if broken or defective. 3. To remove paper, release paper clamp by lifting up on lever, and disengaging it from the tab on the sanding base.
OPERATING INSTRUCTIONS INSTALLING HOOK AND LOOP SANDPAPER 1. Before installing sandpaper, make sure the hook and loop fastener base is free of dust and dirt and that the sander is unplugged with the ON/OFF switch in the OFF position. 2. The sanding base will hold any hook and loop sandpaper without clamps or glue. Simply line up the sandpaper with the hook and loop fastener base and press together, making sure front edge of the sandpaper is aligned with the front edge of the hook and loop fastener base. 3.
SANDPAPER SELECTION Choosing the right size, grit and type of sandpaper maximizes the quality of your sanded finish. Aluminum oxide, silicon carbide, and other synthetic abrasives are best for power sanding as nautral abrasives, such as flint and garnet, are too soft for economical use in power sanding. In general, coarse grit will remove the most material and finer grit will produce the best finish in all sanding operations.
EXPLODED VIEW AND PARTS LIST 10
EXPLODED VIEW AND PARTS LIST Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Stock # 6313-001 6313-002 6313-003 6313-004 6313-005 6313-006 6313-007 6313-008 6313-009 6313-010 6313-011 6313-012 6313-013 6313-014 6313-015 6313-016 6313-017 6313-018 6313-019 6313-020 Description Label Screw Switch button Right housing Sleeve Brush box Brush holder Carbon brush Switch Screw Cable clip Bearing holder Bearing Rotor Stator Bearing holder bearing Eccentric fan Bearing Washer Item 21 22 23 24 25 26 27 28
LIMITED ONE YEAR WARRANTY WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of ONE (1) year from date of purchase.
