Product Manual
13
E
F
A
C
D
B
Fig. 6
A - Work rest (right)
B - Washer
C - Star washer
D - Work rest bracket
E - Work rest knob
F - Bracket knob
G - Pin
H - Carriage bolt
I - Washer
Fig. 7
A - Battery cover
B - Batteries AAA
A
B
Fig. 8
Fig. 9
A - Bolt
B - Washers
C - Lock washer
D - Hex nut
D
C
B
A
B
A - Coolant tray bracket
B - Coolant tray
A
B
G
H
I
13
E
F
A
C
D
B
Fig. 6
A - Work rest (right)
B - Washer
C - Star washer
D - Work rest bracket
E - Work rest knob
F - Bracket knob
G - Pin
H - Carriage bolt
I - Washer
Fig. 7
A - Battery cover
B - Batteries AAA
A
B
Fig. 8
Fig. 9
A - Bolt
B - Washers
C - Lock washer
D - Hex nut
D
C
B
A
B
A - Coolant tray bracket
B - Coolant tray
A
B
G
H
I
13
E
F
A
C
D
B
Fig. 6
A - Work rest (right)
B - Washer
C - Star washer
D - Work rest bracket
E - Work rest knob
F - Bracket knob
G - Pin
H - Carriage bolt
I - Washer
Fig. 7
A - Battery cover
B - Batteries AAA
A
B
Fig. 8
Fig. 9
A - Bolt
B - Washers
C - Lock washer
D - Hex nut
D
C
B
A
B
A - Coolant tray bracket
B - Coolant tray
A
B
G
H
I
INSTALLING THE COOLANT TRAY (FIG. 4)
Place the coolant tray (Fig. 4 - L) over the coolant tray bracket
then firmly push tray down onto the bracket to secure it in place.
INSTALLING THE LED BATTERIES (FIG. 5 & 6)
1. The LED light switch is on top of the spark shield assembly.
Make sure that the LED button has been pushed to the OFF posi-
tion when installing batteries.
2. Remove the battery covers from the top of the LED assem-
blies.
3. Install the AAA batteries (O) inside the battery compartments
according to the polarity indicators, then replace the battery
covers.
4. Repeat the steps above for the other LED light.
MOUNTING TO THE WORK SURFACE (FIG. 7)
The bench grinder should be firmly attached to a reliable work
surface using mounting hardware (not included) installed
through the mounting holes on the base of the grinder. This
will prevent the bench grinder from vibration, walking or tipping
during operation.
NOTE: This bench grinder is compatible with the WEN 4288
Cast Iron Bench Grinder Pedestal Stand.
1. Prepare 1/4 in. bolts, flat washers, lock washers and hex nuts
(not included). The bolt length should be 1-1/2 in. longer than
the thickness of the workbench.
2. Locate and mark the holes where the grinder is to be mounted
onto the work surface.
NOTE: If mounting to a work bench, drill two 3/8 in. diameter
holes through the workbench.
3. Place the bench grinder onto the workbench, aligning holes in
base with holes in the workbench.
4. Insert two 1/4 in. diameter bolts and washers and attach with
nuts securely.
ASSEMBLY & ADJUSTMENTS
WARNING! Always make sure your bench grinder is se-
curely mounted to a workbench. Failure to do so could result
in an accident resulting in possible serious personal injury.
L
Coolant Bracket
Fig. 4
14
Fig. 10
Fig. 13
Fig. 14
Fig. 11
A - On/Off switch
A
Fig. 12
A - Work rest
A
C
A
B
A - Vise
B - Lawn mower blade
C - Screwdriver
A
A
CHISEL SHARPENING
A - LED light switch
LED Switch
Fig. 5
Battery Cover
O
Fig. 6
Fig. 7
Bolt
Washer
Washer
Hex Nut
Lock Washer
12