MODEL MM1214 12" DUAL-BEVEL SLIDING COMPOUND MITER SAW For replacement parts visit WENPRODUCTS.COM IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions.
TABLE OF CONTENTS Specifications............................................................................................ 2 Introduction.............................................................................................. 3 General Safety Rules................................................................................. 4 Specific Safety Rules for Your Miter Saw.................................................. 6 Electrical Information.........................................................
INTRODUCTION Thanks for purchasing the WEN Miter Saw. We know you are excited to put your tool to work, but first, please take a moment to read through the manual. Safe operation of this tool requires that you read and understand this operator’s manual and all the labels affixed to the tool. This manual provides information regarding potential safety concerns, as well as helpful assembly and operating instructions for your tool. SAFETY ALERT SYMBOL: Indicates danger, warning, or caution.
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: Read and understand all warnings, cautions and operating instructions before using this tool. Failure to follow all instructions listed below may result in personal injury, electric shock, fire and/or tool damage. WORK AREA SAFETY 1. KEEP WORK AREA CLEAN AND WELL LIT. Cluttered or dark areas invite accidents. 2.
GENERAL SAFETY RULES POWER TOOL USE AND CARE 1. DO NOT FORCE THE POWER TOOL. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 2. DO NOT USE THE POWER TOOL IF THE SWITCH DOES NOT TURN IT ON AND OFF. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 3.
SPECIFIC RULES FOR YOUR MITER SAW WARNING: Do not operate the miter saw until you have read and understood the following instruc- tions and the warning labels. SAW BLADE SAFETY 1. Always wear protective gloves when handling saw blades. 2. Only use blades with correct size and type for both your miter saw and your workpiece. • The rated diameter of the saw blade is 12" with a 1" arbor. • The no-load speed of the miter saw is 3800 RPM.
SPECIFIC RULES FOR YOUR MITER SAW WARNING: Do not operate the miter saw until you have read and understood the following instruc- tions and the warning labels. 3. Examine the miter saw for any damaged or missing parts. Replace or repair damaged parts before operation. Periodically check that all nuts, bolts and other fasteners are properly tightened. SECURE YOUR WORKPIECE 1. Always position the workpiece on the miter table and firmly against the fence.
ELECTRICAL INFORMATION GROUNDING INSTRUCTIONS IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides the path of least resistance for an electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching outlet that is properly installed and grounded in accordance with ALL local codes and ordinances. DO NOT MODIFY THE PLUG PROVIDED.
UNPACKING & TRANSPORTATION UNPACKING With the help of a friend or trustworthy foe, carefully remove the miter saw from the packaging. Make sure to take out all contents and accessories. Do not discard the packaging until everything is removed. Check the packing list below to make sure you have all of the parts and accessories. If any part is missing or broken, please contact our customer service at 1-800-232-1195. PACKING LIST A B E A. B. C. D. E. F. G.
KNOW YOUR MITER SAW TOOL PURPOSE Miter Saws allow you to easily make cuts at a variety of angles. Refer to the following diagrams to become familiarized with all the parts and controls of your miter saw. The components will be referred to later in the manual for assembly and operation instructions. F G E H D I C J B K A L P A. B. C. D. E. F. 10 Table Extension Fence Clamp Assembly LED Work Light Slide Lock Knob Trigger Locks G. H. I. J. K. L.
KNOW YOUR MITER SAW T U S V R W Q X Y Z Q. R. S. T. Spindle Lock Operating Handle Carrying Handle Power Trigger U. V. W. X. Laser ON/OFF Work Light ON/OFF Rear Carrying Handle Support Stand Y. Bevel Scale Z.
ASSEMBLY & ADJUSTMENTS WARNING: Do not plug in or turn on the tool until it is fully assembled according to the instructions. Read through and become familiarized with the following procedures of handling and adjusting your miter saw. Failure to follow the safety instructions may result in serious personal injury. GUARD OPERATION 3 NOTE: Keep hands clear of the blade when the operating handle is lowered. Do not interfere with the proper movement of the blade guard.
ASSEMBLY & ADJUSTMENTS Fig. 4 1 2 Fig. 5 Clamp Assembly 5 1 2 3 4 ADJUSTING THE MITER ANGLE The miter table can be adjusted from 0° to 45° to both left and right to create miter cuts. 1. Loosen the miter lock knob (Fig. 4 - 5) by turning it one or two turns counterclockwise. 2. Pull up on the miter stop lever (Fig. 4 - 4) to unlock the table. While holding the miter stop lever up, adjust the table to the desired angle. The miter scale indicator (Fig. 4 - 3) will point towards the selected angle.
ASSEMBLY & ADJUSTMENTS WARNING: Do not plug in or turn on the tool until it is fully assembled according to the instructions. Read through and become familiarized with the following procedures of handling and adjusting your miter saw. Failure to follow the safety instructions may result in serious personal injury. INSTALLING THE SUPPORT STAND The support stand offers additional stability for your miter saw. Follow the instructions below to install the support stand. Fig. 6 1 1.
ASSEMBLY & ADJUSTMENTS WARNING: Do not plug in or turn on the tool until it is fully assembled according to the instructions. Read through and become familiarized with the following procedures of handling and adjusting your miter saw. Failure to follow the safety instructions may result in serious personal injury. Fig. 9 1 Fig. 10 2 SQUARING THE FENCE WITH THE BLADE SQUARING THE TABLE WITH THE BLADE 1. Lower the saw arm down to the lower position and lock the release knob.
ASSEMBLY & ADJUSTMENTS WARNING: Do not plug in or turn on the tool until it is fully assembled according to the instructions. Read through and become familiarized with the following procedures of handling and adjusting your miter saw. Failure to follow the safety instructions may result in serious personal injury. 5. Flip the bevel stop block (Fig. 11 - 4) up. Loosen the zero stop lock nut (Fig. 11 - 2) and adjust the zero stop screw (Fig. 11 - 1) until the table is 90° with the blade.
ASSEMBLY & ADJUSTMENTS WARNING: Do not plug in or turn on the tool until it is fully assembled according to the instructions. Read through and become familiarized with the following procedures of handling and adjusting your miter saw. Failure to follow the safety instructions may result in serious personal injury. Wear gloves while changing the blade. CHANGING THE SAW BLADE Fig. 13 DANGER! Never try to use a blade larger than the stated capacity of the saw. Do not use a blade thicker than 1.9mm.
ASSEMBLY & ADJUSTMENTS WARNING: Do not plug in or turn on the tool until it is fully assembled according to the instructions. Read through and become familiarized with the following procedures of handling and adjusting your miter saw. Failure to follow the safety instructions may result in serious personal injury. ADJUSTING THE DRIVE BELT 1. Unplug the tool from its power source. Loosen the 3 screws securing the drive belt housing cover (Fig. 17) to the drive belt housing.
OPERATION WARNING: Do not plug in or turn on the tool until it is fully assembled according to the instructions. Read through and become familiarized with the following procedures of handling and adjusting your miter saw. Failure to follow the safety instructions may result in serious personal injury. 1. RAISE THE SAW ARM Before operation, raise the saw arm from the lower position. See section titled, "Raising/Lowering the Saw Arm" on page 12. Fig. 21 CROSS CUT Miter table 0°, Saw arm 0° 2.
OPERATION WARNING: Before operating the miter saw, make sure to equip yourself with a dust mask, ear protection, and safety glasses for protection from possible injuries. Tie back long hair and do not wear loose clothing or jewelry. DO NOT look into the laser beam, this can cause serious eye damage or blindness. Do not wear gloves while operating the saw. 5.
MAINTENANCE WARNING: To avoid accidents, turn OFF and unplug the tool from the electrical outlet before cleaning, adjusting, or performing any maintenance work. WARNING: Any attempt to repair or replace electrical parts on this tool may be hazardous. Servicing of the tool must be performed by a qualified technician. When servicing, use only identical WEN replacement parts. Use of other parts may be hazardous or induce product failure.
TROUBLESHOOTING GUIDE WARNING: Stop using the tool immediately if any of the following problems occur. Repairs and replace- ments should only be performed by an authorized technician. For any questions, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email us at techsupport@wenproducts.com.
EXPLODED VIEW & PARTS LIST 201 202 203 204 205 206 207 211 210 209 208 200 199 198 197 196 194 195 193 23
EXPLODED VIEW & PARTS LIST 24 No. 1 2 Part. No.
EXPLODED VIEW & PARTS LIST No. 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 Part. No.
EXPLODED VIEW & PARTS LIST 26 No. 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 Part. No.
WARRANTY STATEMENT WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship during personal use for a period of two (2) years from date of purchase or 500 hours of use; whichever comes first.
THANKS FOR REMEMBERING