WS2355KU (CMT18W) Cordless Oscillation Tool 2 EN
1 2 3 8 7 6 5 4
2 1 3 Fig.A2 Fig.A1 4 5 Fig.B Fig.A3 100% 0% Fig.D Fig.C 1 2 Fig.E2 Fig.
Fig.E2 Fig.E1 ON OFF Fig.F Fig.G Fig.H Fig.
PRODUCT SAFETY WARNING: Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints; • Crystalline silica from bricks and cement and other masonry products; • Arsenic and chromium from chemically-treated lumber.
moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. h) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control. SAFETY WARNINGS FOR BATTERY PACK a) Do not dismantle, open or shred battery pack. b) Do not expose battery pack to heat or fire. Avoid storage in direct sunlight. c) Do not short-circuit a battery pack. Do not store battery packs haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by other metal objects.
• Consult the dealer or an experienced radio/TV technician for help. SYMBOLS To reduce the risk of injury, user must read instruction manual Warning Wear ear protection Wear eye protection Wear dust mask Batteries may enter water cycle if disposed improperly, which can be hazardous for ecosystem. Do not dispose of waste batteries as unsorted municipal waste. Do not burn Li-Ion battery, battery must be recycled POSITEC Inc.
COMPONENT LIST 1. 2. 3. 4. 5. 6. 7. 8. Tool-less accessory clamping lever On/off switch Battery pack release button Battery pack Variable speed control Venting slot LED light Flange TECHNICAL DATA Type WS2355KU (2355 - designation of machinery, representative of cordless multi- function tool) Voltage Max* 20V No load speed 5000-20000/min Oscillations angle 3.0° Machine weight 2.65lbs Battery capacity (WS9970) 2.
OPERATION INSTRUCTIONS NOTE: Before using the tool, read the instruction book carefully. INTENDED USE The power tool is intended for sawing and separating wooden materials, plastic, plaster, non-ferrous metals and fasteners (e.g. nails and clamps) as well as for working on soft wall tiles and for dry grinding of small surfaces. It is especially suitable for working close to edges and for flush cutting. ASSEMBLY 1.
4. TO INSTALL THE BATTERY PACK (SEE FIG. E2) Slide the fully charged battery pack onto the tool with sufficient force until it clicks into position. OPERATION 1. ON/OFF SWITCH (SEE FIG. F) To start the machine, push the On/Off switch forward so that the “1” mark is indicated on the switch. To switch off the machine, push the On/Off switch toward the rear so that the “O” mark is indicated on the switch. 2. VARIABLE SPEED CONTROL (SEE FIG. G) Select oscillation frequency (speed) while the motor is running.
APPLICATION WARNING: The sawing teeth are very sharp. Do not touch during mounting and application. The workpiece must be clamped tightly before it is cut.
FCC Part 15 Supplier’s Declaration of Conformity Product Description: Battery charger Model Number: WS9924U Trade Name: WESCO This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Responsible Party : Positec USA, Inc. 10130 Perimeter Parkway, Charlotte, NC 28216 USA Tel.
