Quick Guide Smart Camera with Battery V1.1 This guidebook is intended for use by multiple models of battery cameras. Some instructions may not be applicable to all models and are for illustration purpose only.
1. Packing list (Actual products may vary due to different models) Camera Charging cable Mounting sticker Screws Quick Guide Solar panel（Optional） 2.
. Connection Diagram The battery camera supports three connection ways： 1, Connecting to the router (remote use) (Recommend) 2，Connecting to mobile phone directly ( local use ) 3, Pairing to wireless NVR (Base station, NVR) 3
. Connecting 4.1 App installation Search for "EseeCloud" in App Store or scan the QR code here to download the app. Note: Apple mobile phone system requires iOS 9.0 or higher, and Android mobile phone system requires Android 5.1 or higher. 4.2 Log in the App Click “Register” on the app login interface. Sign up and follow the onscreen instructions to complete the registration. Third-party login is supported. 4.3 Insert TF card to the camera Turn off the camera before inserting the card.
2，After the camera is turned on, the voice prompts "start configuration mode", and the red indicator starts blinking. (If not, please long press the reset button for 5 seconds until hearing the voice prompt of "factory Reset") 3，Open the App and click the "+" icon at the upper right corner to scan the QR code on camera label. （If QR code cannot be captured, click “Other ways to add” and choose “Battery camera”.） 4，Click "Add" to proceed to the next step.
5，To view video remotely and connect to WiFi router, select “Remote view”. To view video without network, select Direct Connection (local use only and not recommended). 5.1 Adding for Remote View： （Recommend） 1，Click “Remote View” and select the WiFi to connect, enter the WiFi password, and then click "Next". Follow the onscreen instructions and place the QR code displayed on the mobile phone facing the camera lens (about 6-10 inches away). Follow the prompt voice for the next step.
5.2 Selection of “Direct Connection” (local use only) ： （Not Recommended） 1，“Click "Direct Connection", set the Wi-Fi password for the Wi-Fi signal that comes with the camera, and go to next step. Follow the onscreen instructions and align the QR code on the App with the camera lens (about 6-10 inches away), then follow the prompt voice to the next step. 2. According to the guide interface, after connecting the mobile phone to the WiFi that comes with the camera, return to the App.
5. Function Part Preview, playback, alarm notification, function setting Play, Enter the preview Alarm notification，View interface alarm screenshot / video Share, share the device Playback video with family.
Icon explain Icon SD/HD，definition switch explain Sound, hear the voice from the camera. Screenshot, save the current Recording, save the current screenshot to your phone. video to your phone. Full screen, full screen view. Menu setting speak to the camera side. Video playback. More features Siren Light, switched to infrared Detect Ai switch, opened by light（IR) or white light（on) default. After closed, it will not be triggered.
4，Share the device After entering the sharing interface, select the permissions and the validity period of the QR code for sharing. Click the “Complet ” on the upper right corner, share the generated QR code to other people. （Other people need to download the APP, register a new account and log in, then scan the QR code you shared to add the device successfully.） 5，Menu setting Push message settings: The APP pushes alarm messages, which is enabled by default.
Smart detection alarm: Intelligent detection alarm (open by default, if it is closed, it can only be actively previewed through the APP,and it will not record or push alarm messages) Motion detection sensitivity: try lowering the sensitivity if detection alarms are too frequent. Siren setting: when turned on, the camera will sound the alarm sound when triggered Storage settings: Check the TF card status.The device defaults to loop recording.
6. Installation Surveillance Area: When installing the camera, the PIR sensor should not be vertically aligned with the moving objects, as it may not sensitive to movement. It is recommended that the camera be tilted more than 15 degrees to capture motions. Notice: PIR sensor is sensitive to hot and cold air flow. Avoid installing the camera at a place where airflow is stirred up. For example: the air outlet of the air conditioner, the cooling vent of equipment, locations next to fans or curtain, etc.
7. Charging instructions During use, the camera needs to be charged when the low battery indicator shows or the App pushes low battery message.(NOTE: DC5V power adapter is not included in package.Please use your phone charger.) 1. Insert the power supply into the USB port of the camera. 2. When charging, the green indicator light of the camera will be continuous blinking. You can also confirm the charging status by the charging icon.
8. Help FAQ Q1：Why is the pairing network unsuccessful? 1.Please make sure that the distance among the camera, the router and the mobile phone should be close enough when configuring the network. 2. Please make sure that the WIFI signal connected to the mobile phone must be 2.4G, not a 5G WIFI signal. 3. Please check whether the WIFI name and password are correct. 4. Please long press the reset button for 5 seconds and try again after restoring the camera to the factory.
Q4：Why does the battery drain quickly? 1. Check the daily triggered alarm messages. If there are more false triggers, please lower the trigger sensitivity in the settings. 2. Go into the setting menu and change to the ‘ Optimal Battery Life ’.and ‘Record only the scene where people appear’. 3. Check the signal strength of the camera. If the signal is too weak, try to change the position of the camera or router to improve the signal transmission between them. Q5：Why is there no playback? 1.
Q6： Why my phone does not have an alarm push function or two way audio? 1，Check your mobile phone permission settings, and make sure that enable the notification permission of " "EeeCloud" App. 2，Open your phone's Settings > Apps and Notifications, select Apps and Notification Management respectively, find the "EeeCloud" app, and turn on all permissions.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
