User`s manual

17
6. Place the Console Base (45) on the Right Handrail (5)
and the Left Handrail (not shown). Attach the Console
Base with four 3/4” Screws (77) (only two Screws are
shown). Do not tighten the Screws yet.
Insert the Wire Harness (53) through the two indicated
plastic ties on the Console Base (45). Next, insert the
Wire Harness up through the opening beside the Wire
Cover (50). Make sure that the Wire Cover is securely at-
tached to the Console Base.
See drawing 6a. Look at the top of the Console Base
(45). Insert the Wire Harness (53) through the plastic tie
on top of the Console Base.
Tighten the two Crossbar Screws (86) (only one is
shown).
6
8
45
50
Ties
86
5
53
Tie
45
77
53
6a
65
53
5
86
86
4
5
89
5. See the inset drawings and identify the two Crossbar
Screws (86); be careful not to confuse the Crossbar
Screws with the 3/4” Screws (77). The Crossbar
Screws are slightly larger than the 3/4” Screws.
Hold the Crossbar (65) on the small brackets on the
Handrails (4, 5). Attach the Crossbar to the small brack-
ets with the two Crossbar Screws (86). Do not tighten
the Crossbar Screws yet.
Attach the end of the ground wire on the Wire Harness
(53) to the small hole in the left side of the Right Handrail
(5) with the Silver Ground Screw (89).
86
Small Bracket
Small Bracket
77
49
7
7. Press the Book Rack (49) onto the Console Base (45) in
the location shown.
45
PROBLEM: The walking belt slows when walked on
SOLUTION:
a.
If an extension cord is needed, use only a 3-conductor, 1mm
2
(14-gauge) cord that is no longer
than 1.5 m (5 ft.).
b. If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear
roller bolts counterclockwise, 1/4 of a turn. When the
walking belt is properly tightened, you should be able
to lift each side of the walking belt 5 to 7 cm (2 to 3
in.) off the walking platform. Be careful to keep the
walking belt centred. Plug in the power cord, insert
the key and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
c. If the walking belt still slows when walked on, please call our Customer Service Department.
PROBLEM: The walking belt is off-centre or slips when walked on
SOLUTION:
a. If the walking belt is off-centre, first remove the key
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the hex key to turn
the left rear roller bolt clockwise 1/2 of a turn; if the
walking belt has shifted to the right, turn the bolt
counterclockwise 1/2 of a turn. Be careful not to over-
tighten the walking belt. Plug in the power cord, insert
the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centred.
b. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using the
hex key, turn both rear roller bolts clockwise, 1/4 of a
turn. When the walking belt is correctly tightened, you
should be able to lift each side of the walking belt 5 to
7 cm (2 to 3 in.) off the walking platform. Be careful to
keep the walking belt centred. Plug in the power cord,
insert the key, and walk on the treadmill for a few min-
utes. Repeat until the walking belt is properly tight
-
ened.
b
a
b
5–7cm
Rear Roller
Adjustment Bolts