User`s manual

6 15
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not
d
ispose of the packing materials until assembly is completed.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This does not
a
ffect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a
soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex keys and your own phillips screwdriver , two
adjustable spanners , and needlenose pliers .
To identify the assembly hardware, see the PART IDENTIFICATION CHART in the center of this manual.
UP
RIGHT
DOWN
LEFT
DOWN
RIGHT
LEFT
UP
WARNING: Do not plug in the power
cord until the treadmill is completely assembled.
68
68
46
13
13
5
5
5
5
62
62
63
63
63
63
1
1. Orient the Base (46) so the holes for the four Base Pads
(63) are on top. Attach the four Base Pads to the Base
with the four 1” Tek Screws (5).
Attach the two Wheels (68) to the Base (46) with two 2”
Bolts (62) and two 3/8” Nuts (13) as shown.
Do not
overtighten the Bolts; the Wheels must be able to
turn freely.
2. Identify the Right Handrail (59), which has a large hole in
one side. Have a second person hold the Base (46) in a
vertical position, with the Base Pads (63) on the side
shown. Next, hold the Right Handrail against the Base so
the large hole is in the position shown. Attach the Right
Handrail with two 2 1/2” Bolts (65) and two 5/16” Nuts
(61), and a 2” Bolt (62) and a 3/8” Nut (13) as shown.
Do
not tighten the Bolts yet.
Attach the Left Handrail (53) to the Base (46) in the
same way.
61
46
63
65
62
59
53
13
63
63
Large Hole
65
2
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
k
g) to raise, lower or move the treadmill.
1. Hold the treadmill with your hands in the location shown
by the arrow at the right. To decrease the possibility of
injury, bend your legs and keep your back straight.
As you raise the frame, make sure to lift with your
legs rather than your back.
Raise the frame about
halfway to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the lock knob to
the left and hold it. Raise the frame until it passes the
lock pin. Slowly release the lock knob. Make sure that
the frame is securely held by the lock pin.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 30° C (85° F).
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the
frame is securely held by the lock pin.
1. Hold the handrails, and place one foot against one of the
wheels.
2. T
ilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location.
To
reduce the risk of injury, use extreme caution while
moving the treadmill. Do not move the treadmill over
an uneven surface.
3. Place one foot against one of the wheels, and carefully
lower the treadmill to the storage position.
Base
Wheel
Handrails
Frame
Lock
Pin
Lock
Knob
Closed