User`s manual

138
6
. Carefully pull the opposite end of the tape to pull the
W
ire Harness (60) up through the Right Handrail (59)
and out of the hole in the side of the Right Handrail.
Remove the tape from the Wire Harness (60).
59
Tape
6
0
6
7. Orient the Crossbar (91) with the large hole at the right
of the smaller hole as shown. Set the Crossbar against
the Handrails (53, 59) with the brackets on the Crossbar
aligned with the two small holes in each Handrail. Attach
the Crossbar with two Crossbar Star Washers (93) and
two Crossbar Screws (92). Do not tighten the
Crossbar Screws yet.
With the help of as second person, hold the console
assembly near the Crossbar (91). Connect the pulse
wire from the Crossbar to the pulse wire from the con-
sole assembly. The connectors should slide easily into
each other and snap into place. If they do not slide easi-
ly and snap into place, turn a connector and then insert it.
Insert the ground wire through the two plastic ties shown
in step 8. Attach the end of the ground wire to the small
hole in the side of the Right Handrail (59) with a Silver
Ground Screw (69).
Pulse
Wires
Console
Assembly
59
53
92
91
92
93
93
7
52
91
Ties
59
8
8. Place the Console Base (52) on the Crossbar (91), Right
Handrail (59) and the Left Handrail (not shown). Be care-
ful not to pinch any wires.
Attach the Console Base with
four 3/4” Screws (2) (only two Screws are shown).
Do not
overtighten the Screws.
Insert the Wire Harness (60) through the two indicated
plastic ties on the Console Base (52). Next, touch the
Right Handrail (59) to discharge any static. See the
inset drawing. Insert the connector on the end of the Wire
Harness into the red socket beneath the console. The
connector should slide easily into the socket and snap
into place. If the connector does not slide easily and snap
into place, turn the connector and then insert it.
Make sure that the connector and wire appear as shown
in the inset drawing.
IF THE CONNECTORS ARE NOT
INSERTED PROPERL
Y, THE CONSOLE MAY BE
DAMAGED WHEN THE POWER IS TURNED ON.
60
2
Socket
60
Ground
Wire
The Time/Pace zone of
the display will show
t
he total number of
hours that the treadmill
h
as been used.
The Distance zone of
the display will show the
total number of miles
that the walking belt has
moved.
IMPORTANT: If a “d”
appears in the Digital
Speed zone of the dis-
play, the console is in
the “demo” mode. This
mode is intended to be
used only when a treadmill is displayed in a store.
When the console is in the demo mode, the power
cord can be plugged in, the key can be removed
from the console, and the indicators in the display
will automatically appear in a preset sequence.
The buttons on the console will not operate.
If a
“d” appears when the information mode is
selected, press the Speed decrease button so
the “d” disappears.
To exit the information mode, remove the key from
the console.
Measure your heart rate if desired.
Before using
the handgrip
pulse sensor,
remove the
sheets of clear
plastic from the
metal contacts.
In addition,
make sure that
your hands are clean.
T
o measure your heart rate, stand on the foot
rails and hold the metal contacts on the pulse
handgrips—avoid moving your hands. When
your pulse is detected, the heart symbol in the
Pulse zone of the display will begin to flash each
time your heart beats, one or two dashes will
appear, and then your heart rate will be shown.
F
or the most accurate heart rate reading, continue
to hold the contacts for about 15 seconds.
If the displayed heart rate appears to be too high
or too low, or if your heart rate is not displayed, lift
your hands off the metal contacts for a few sec-
onds. Then, place your hands on the metal con-
tacts as described above. Remember to stand still
while measuring your heart rate.
When you are finished exercising, remove the
key.
Step onto the foot rails and press the Stop button.
Next, remove the key from the console and put it in
a secure place.
Note: If the display remains lit
after the key is removed, the console is in the
demo mode. See step 6 on page 12 and turn off
the demo mode.
When you are finished using the treadmill,
switch the on/off switch to the “off” position
and unplug the power cord.
HOW TO USE A SPEED PROGRAM
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
11.
Select a speed program.
To select a speed pro-
gram, press the
Program button repeat-
edly until the number 1,
2, 3, 4, or 5 appears in
the Analog Speed zone
of the display. When a speed program is select-
ed, the
Time/Pace zone will show how long the
program will last, and the Digital Speed zone will
flash the maximum speed setting of the program
for a few seconds.
2
1
8
7
Metal
Contacts
69