Model No. WETL30708.0 Serial No. Write the serial number in the space above for reference. Serial Number Decal QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if there are missing parts, please contact us at the numbers or addresses listed below: Call: 08457 089 009 Outside UK: 0 (44) 113 3877133 Fax: 0 (44) 113 3877125 E-mail: csuk@iconeurope.com Write: ICON Health & Fitness, Ltd.
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ASSEMBLY . . . . . . . . . . .
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your treadmill before using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 1. Before beginning this or any exercise program, consult your physician. This is especially important for persons over age 35 or persons with pre-existing health problems. cuit.
20. Do not attempt to raise, lower, or move the treadmill until it is properly assembled. (See ASSEMBLY on page 6, and HOW TO FOLD AND MOVE THE TREADMILL on page 20.) You must be able to safely lift 45 lbs. (20 kg) to raise, lower, or move the treadmill. 24. Never drop or insert any object into any opening on the treadmill. 25. 21. When folding or moving the treadmill, make sure that the storage latch is holding the frame securely in the storage position. 22.
BEFORE YOU BEGIN Thank you for selecting the new WESLO® COMPACT SL treadmill. The COMPACT SL treadmill offers a selection of features designed to make your workouts at home more effective. And when youʼre not exercising, the unique treadmill can be folded up, requiring less than half the floor space of other treadmills. ing this manual, please see the front cover of this manual. To help us assist you, please note the product model number and serial number before contacting us.
ASSEMBLY Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This does not affect treadmill performance.
1. Make sure that the power cord is unplugged. 1 Orient the Base (101) as shown. Attach four Base Feet (100) to the Base (101) in the locations shown with four M4.2 x 19mm Tek Screws (14). 14 100 14 101 100 14 100 14 100 2. Identify the Right Upright (98), which has a large hole in the location shown. 2 Orient the Right Upright (98) and the Base (101) as shown.
3. Orient the Left Upright (96) and the Base (101) as shown. Attach the Left Upright to the Base with two M10 x 53mm Patch Bolts (18) and two M10 Flat Washers (16); do not fully tighten the Patch Bolts yet. 3 101 96 16 18 4. With the help of a second person, raise the Uprights (96, 98) so the Base (101) is flat on the floor as shown. Next, position the front of the Frame (67) between the Uprights. Wire Tie 4 96 See the inset drawing. Locate the wire tie inside the lower end of the Right Upright (98).
5. Have a second person raise the Frame (67) and hold it until step 6 is completed. 5 Hold an Upright Spacer (54) between the Right Upright (98) and the Frame (67) as shown. Attach the Right Upright to the Frame with an M10 x 110mm Bolt (15), an M10 Washer (4), and an M10 Star Washer (8); do not fully tighten the Patch Bolt yet. Be careful not to pinch the Wire Harness (97). 98 67 54 4 97 6. Hold the remaining Upright Spacer (54) between the Left Upright (96) and the Frame (67) as shown.
7. Have a second person lift and hold the Frame (67) until step 8 is completed. 7 Next, place the cylinder end of the Gas Spring (1) near the bracket on the Base (101). 67 See the two small inset drawings. Using your fingernail or the end of a screwdriver, press on the end of the Gas Spring Pin (7) to loosen it from the Gas Spring (1). Next, rotate the Gas Spring Pin and pull it out of the Gas Spring. Be careful to avoid losing the Gas Spring Pin. 7 See the lower drawing.
9. Identify the Right Handrail Cover (95) and the Left Handrail Cover (93). Slide the end of the Right Handrail (94) through the hole in the Right Handrail Cover, and slide the end of Left Handrail (92) through the hole in the Left Handrail Cover. 9 95 Attach the Handrail Covers (93, 95) to the Handrails (92, 94) with two M4.2 x 19mm Screws (10) in the locations shown. 93 Hole 10. Set the Console (52) face down on a soft surface to avoid scratching the Console.
11. Attach the Right Handrail (94) to the Console (52) with an M5 x 16mm Screw (13), an M5 Star Washer (12), and two M4.2 x 19mm Screws (10). Make sure that no wires are pinched. Start all three Screws before tightening any of them. Tighten the M5 x 16mm Screw and then tighten the M4.2 x 19mm Screws. Do not overtighten the Screws. 11 94 13 12 Attach the Left Handrail (92) to the other side of the Console (52) in the same way. Note: There are no wires on the left side of the Console.
. Attach the Console (52) to the Uprights (96, 98) with six M8 x 16mm Bolts (17) and six 5/16" Star Washers (2). Start all six Bolts before tightening any of them. 13 2 52 17 2 17 2 96 2 17 98 14. With the help of a second person, lower the Uprights (96, 98) as shown. 14 See the lower drawing. Position the Uprights (96, 98) so that the Frame (67) is centered between the Uprights.
15. Attach the Latch Housing (62) to the Left Upright (96) with two #10 x 1" Tek Screws (43). Make sure that the Latch Housing is oriented as shown. Do not overtighten the Screws. 15 43 16. Place the treadmill in the storage position (see HOW TO FOLD AND MOVE THE TREADMILL on page 20). 16 Insert the Incline Pins (24) at the desired incline level (see HOW TO CHANGE THE INCLINE OF THE TREADMILL on page 19). 24 62 96 24 Lower the treadmill (see HOW TO LOWER THE TREADMILL FOR USE on page 21). 17.
OPERATION AND ADJUSTMENT THE PRE-LUBRICATED WALKING BELT Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear. HOW TO PLUG IN THE POWER CORD This product must be earthed.
CONSOLE DIAGRAM Key Clip FEATURES OF THE CONSOLE To turn on the power, see page 17. To use the manual mode of the console, see page 17. To use a speed workout, see page 19. The treadmill console offers a selection of features designed to make your workouts more effective. When you select the manual mode of the console, you can change the speed of the treadmill with the touch of a button. As you exercise, the console will display continuous exercise feedback.
HOW TO TURN ON THE POWER HOW TO USE THE MANUAL MODE IMPORTANT: If the treadmill has been exposed to cold temperatures, allow it to warm to room temperature before turning on the power. If you do not do this, you may damage the console displays or other electrical components. Plug in the power cord (see page 15). Next, locate the reset/off circuit breaker on the treadmill frame near the power cord. Switch the circuit breaker to the reset position. 1. Insert the key into the console.
4. Follow your progress with the displays. ment is selected, remove the key, insert the key into the console while holding down the Stop button, and then release the Stop button. An “M” for metric kilometers or an “E” for English miles will appear in the upper display. Press the Digital Speed increase button to change the unit of measurement if desired. When the desired unit of measurement is selected, remove the key and then reinsert it.
HOW TO USE A SPEED WORKOUT To stop the workout temporarily, press the Stop button. The time will begin to flash in the display. To restart the workout, press the Start button or the Digital Speed increase button. The walking belt will begin to move at 2 km/h. When the next segment of the workout begins, the treadmill will automatically adjust to the speed setting for the next segment. 1. Insert the key into the console. See HOW TO TURN ON THE POWER on page 17. 2. Select one of the four speed workouts.
HOW TO FOLD AND MOVE THE TREADMILL HOW TO FOLD THE TREADMILL FOR STORAGE Remove the key and unplug the power cord. CAUTION: You must be able to safely lift 45 lbs. (20 kg) to raise, lower, or move the treadmill. 1. Hold the metal frame firmly in the location shown by the arrow at the right. CAUTION: To decrease the possibility of injury, do not lift the frame by the plastic foot rails. Make sure to bend your legs and keep your back straight as you raise the frame.
HOW TO LOWER THE TREADMILL FOR USE 1. Hold the treadmill with your right hand as shown. Pull the latch knob to the left and hold it. Pivot the frame down until it is past the latch pin. Slowly release the latch knob. Frame Latch Pin Latch Knob 2. Hold the metal frame firmly with both hands and lower it to the floor. CAUTION: Do not grip only the plastic foot rails or drop the frame to the floor. Bend your legs and keep your back straight.
TROUBLESHOOTING Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See page 15.) If an extension cord is needed, use only a 3-conductor, 14-gauge (1 mm2) cord that is no longer than 5 ft. (1.5 m).
Locate the Reed Switch (55) and the Magnet (49) on the left side of the Pulley (58). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the M4 x 13mm Tek Screw (29), move the Reed Switch slightly, and then retighten the Screw. Reattach the Motor Hood (not shown), and run the treadmill for a few minutes to check for a correct speed reading. 1/8 in.
PROBLEM: The walking belt is off-center or slips when walked on SOLUTION: a. If the walking belt is off-center, first remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left idler roller bolt clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left bolt counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes.
EXERCISE GUIDELINES WARNING: Before beginning this Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of time. During the first few minutes of exercise, your body uses carbohydrate calories for energy. Only after the first few minutes of exercise does your body begin to use stored fat calories for energy. If your goal is to burn fat, adjust the intensity of your exercise until your heart rate is near the lowest number in your training zone.
PART LIST—Model No. WETL30708.0 To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual. Key No. Qty. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 1 6 2 2 2 1 2 2 2 15 1 2 2 10 2 4 6 4 5 1 4 2 2 2 2 2 2 2 3 12 4 4 2 2 2 2 2 8 3 1 6 4 2 1 1 2 2 1 1 1 Description Key No. Qty.
Key No. Qty. 101 102 103 104 105 106 * * 1 4 2 1 16 1 – – Description Key No. Qty. Base Wheel Spacer Wheel Key/Clip 8" Wire Tie Latch Warning Decal 4" Green Wire, F/R 4" Black Wire, M/F * * * * * * * * – – – – – – – – Description 6" Red Wire, M/F 6" White Wire, 2F 10" White Wire, 2F 10" Blue Wire, 2F 8" Blue Wire, 2F 4" Blue Wire, M/F 4" Black Wire, 2F Userʼs Manual Note: Specifications are subject to change without notice.
24 11 33 36 30 68 71 3 28 38 39 30 48 74 23 19 51 29 31 33 30 25 70 24 39 69 38 36 23 106 20 47 50 21 30 3 19 44 28 31 42 53 32 30 67 30 66 19 30 65 31 55 51 29 37 42 14 58 56 30 21 59 57 49 29 47 19 19 37 30 32 31 64 26 40 26 53 42 30 10 14 57 61 42 EXPLODED DRAWING A—Model No. WETL30708.
EXPLODED DRAWING B—Model No. WETL30708.
EXPLODED DRAWING C—Model No. WETL30708.
EXPLODED DRAWING D—Model No. WETL30708.
ORDERING REPLACEMENT PARTS To order replacement parts, see the front cover of this manual.
