ModelNo.WLEX25190 SerialNo. Writetheserialnumber inthespace aboveforfuturereference. _, I1_ Serial Number Decal \ QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction, tf you have questions, or if there are missing or damaged parts, we will guarantee complete satisfaction through direct assistance from our factory. TO AVOID UNNECESSARY DELAYS, PLEASE CALL DIRECT TO OUR TOLUFREE CUSTOMER HOT UNE.
TABLE OF CONTENTS IMPORTANT PRECAUTIONS ............................................................. BEFORE YOU BEGIN ................................................................... PART IDENTIFICATION CHART ........................................................... ASSEMBLY ........................................................................... HOW TO USE THE EXERCISE CYCLE ...................................................... CONDITIONING GUIDELINES .............................................
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the exercise cycle. 1. Read all instructions in this manual before using the exercise cycle. Use the exercise cycle only as described. 2. It is the responsibility of the owner to ensure that alJ users of the exercise cycle are adequately informed of all precautions, Use the exercise cycle indoors, away from moisture and dust.
BEFORE YOU BEGIN Thank you for selecting the new WESLO _ PURSUIT 618s exercise cycle. The PURSUIT618s blends advanced engineering with contemporary styling to provide you with a low-impact workout in the convenience and privacy of your own home. For your benefit, read this manual carefully before you use the PURSUIT618s. If you have additional questions, please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PART IDENTIFICATION CHART Use the chart below for help identifying the small parts used in assembly. The number in parenthesis below each part refers to the key number of the part, from the PART LIST on page 14. The second number refers to the quantity used in assembly. Note: Some parts may have been pre-attached for shipping purposes. If a part is not found in the parts bag, check to see if it has been pre-attached, [4 / /" \ / M4 x 16ram Selftapping Screw (9)-1 M8 Split Washer (49)-3 M8 Nylon L
ASSEMBLY Place all parts of the exercise cycle in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed, Assembly requires the included adjustable wrenches __ 1. allen wrench _ , a phillips ¢_ -J_ and two Identify the Front Stabilizer (17), which has Wheels (25) on the ends. Hold the Front Stabilizer (17) against the saddle on the front of the Frame (15).
4. Attach the Handlebar (5) to the Handlebar Post (14) with two MIO x 25ram Button Screws (8) and two MIO Split Washers (41). 4 Insert the Seat Post (20) into the Frame (15). Press the 38.1 mm x 63.5mm Bushing (23) into the Frame. Align one of the holes in the Seat Post with the hole in the Frame. Insert the Seat Knob (29) into the Frame and the Seat Post, and tighten the Seat Knob into the Frame.
HOW TO USE THE EXERCISE CYCLE HOW TO ADJUST THE SEAT DESCRIPTION For effective exercise, the Seat (19) should be at the proper height. As you pedal, there should be a slight bend in your knees when the pedals are in the lowest position. To adjust the Seat, first hold the Seat and Mode Indicators f Mode Button \ unscrew the Seat Knob (29). Align one of the holes The console features seven modes that provide instant exercise feedback during your workouts. The modes are described below.
HOW TO OPERATE THE CONSOLE USING THE PULSE SENSOR 1. To turn on the power, press the mode button or simply begin pedaling. When the power is turned on, the entire display will appear for two seconds. The console will then be ready for operation. To use the pulse sensor, first plug the pulse sensor wire into the jack at the lower edge of the console, as shown in the drawing at the right. SCAN '"'0 l SPEED, o,s..,oE.T,ME, n.!.
CONDITIONING GUIDELINES The following guidelines will help you to plan your exercise program. Remember that proper nutrition and adequate rest are essential for successful results. gy. Only after the first few minutes of exercise does your body begin to use stored fat calories for energy. If your goal is to burn fat, adjust the intensity of your exercise until your heart rate is near the lowest number in your training zone as you exercise.
SUGGESTED STRETCHES The correct form for several basic stretches is shown in the drawings below. Move slowly as you stretch--never bounce. 1. Toe Touch Stretch Stand with your knees bent slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible. Hold for 15 counts, then relax. Repeat 3 times. Stretches: Hamstrings, back of knees and back. 2. Hamstring Stretch Sit with one leg extended.
MAINTENANCE AND TROUBLE-SHOOTING HOW TO ADJUST THE REED SWITCH Inspect and tighten all parts of the exercise cycle regularly. Replace any worn parts immediately. If the console does not display correct feedback, the reed switch should be adjusted. In order to adjust the reed switch, the Left Side Shield (1) must be removed. Using an adjustable wrench, turn the Left Pedal (28) The exercise cycle can be cleaned with a soft, damp cloth. Avoid spilling liquid on the console.
HOW TO ADJUST THE BELT If the Belt (16) is properly adjusted, reattach the side shields and pedals. If the Belt needs to be adjusted, loosen the M8 Washer Nut (37) on each side of the Flywheel Assembly (32). To tighten the Belt, turn the two 6 M6 Nuts (47) clockwise; to loosen the Belt, turn the Nuts counterclockwise. Make sure The exercise cycle features a precision belt that must be kept properly adjusted. If the belt causes excessive noise or slips as you pedal, the belt should be checked.
PARTS LIST-- Model No. WLEX25190 Key No. Qty. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 1 1 2 1 1 2 1 5 4 1 1 1 1 1 1 1 1 1 1 1 8 1 1 2 2 4 1 1 1 4 1 Description R1099A Key No. Qty.
EXPLODED DRAWING-- Model No.
HOW TO ORDER REPLACEMENT PARTS To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).