www.weslo.com Model No. WLEX31310.0 Serial No. Write the serial number in the space above for reference. Serial Number Decal QUESTIONS? If you have questions, or if parts are damaged or missing, DO NOT CONTACT THE STORE; please contact Customer Care. IMPORTANT: Please register this product (see the limited warranty on the back cover of this manual) before contacting Customer Care. 1-866-699-3756 CALL TOLL-FREE: Mon.–Fri., 6 a.m.–6 p.m. MT Sat. 8 a.m.–4 p.m. MT ON THE WEB: www.wesloservice.
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ASSEMBLY . . . . . . . . . . . . .
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your exercise bike before using your exercise bike. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 8. Wear appropriate clothes while exercising; do not wear loose clothes that could become caught on the exercise bike. Always wear athletic shoes for foot protection. 1.
BEFORE YOU BEGIN Thank you for selecting the new WESLO® PURSUIT CT 1.5 exercise bike. Cycling is an effective exercise for increasing cardiovascular fitness, building endurance, and toning the body. The PURSUIT CT 1.5 exercise bike provides a selection of features designed to make your workouts at home more effective and enjoyable. after reading this manual, please see the front cover of this manual. To help us assist you, note the product model number and serial number before contacting us.
ASSEMBLY To hire an authorized service technician to assemble the exercise bike, call 1-800-445-2480. Assembly requires two persons. Place all parts of the exercise bike in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the included tool(s), assembly requires a Phillips screwdriver wrench , and pliers . , an adjustable See the drawings below to identify the small parts needed for assembly.
1. 1 To make assembly easier, read the information on page 5 before you begin. Insert the Rear Stabilizer (6) into the Frame (1). Attach the Rear Stabilizer with four M8 x 60mm Patch Screws (30). 1 30 2. See the inset drawing. Remove the screw and the cardboard tube from the Frame (1). Discard the screw and the cardboard tube. 2 Orient the Front Stabilizer (2) so that the large holes face the Frame (1). Attach the Front Stabilizer (2) to the Frame (1) with two M10 x 70mm Patch Screws (33).
3. While a second person holds the Upright (13) near the Frame (1), connect the Extension Wire (23) to the Reed Switch Wire (39). 3 Next, connect the Resistance Cable (19) to the Lower Resistance Cable (29) in the following way: • See drawing A. Pull upward on the metal bracket on the Lower Resistance Cable (29), and insert the tip of the Resistance Cable (19) into the wire clip inside the metal bracket. 13 • See drawing B.
4. Attach the Handlebar (42) to the Upright (13) with two M8 x 65mm Bolts (49) and two M8 Locknuts (10). 4 Attach the Water Bottle Holder (3) to the Upright (13) with two M4 x 15mm Screws (48). 10 13 42 49 3 48 5. The Console (16) requires four AA batteries (not included); alkaline batteries are recommended. IMPORTANT: If the Console has been exposed to cold temperatures, allow it to warm to room temperature before inserting batteries.
6. While a second person holds the Console (16) near the Upright (13), connect the wire on the Console to the Extension Wire (23). 6 16 Insert the excess wire downward into the Upright (13). Tip: Avoid pinching the wires. Attach the Console (16) to the Upright (13) with four M4 x 15mm Screws (48). 13 23 Avoid pinching the wires 48 7. Attach the Seat (12) to the Seat Post (5) with four M8 Locknuts (10). Note: The Locknuts may be preattached to the underside of the Seat.
8. Loosen and remove the Seat Post Knob (9) from the Frame (1). 8 Insert the Seat Post (5) into the Frame (1). Adjust the Seat Post to the desired height, and insert the Seat Post Knob (9) through the indicated hole in the Frame into one of the adjustment holes in the Seat Post. Tighten the Seat Post Knob (9). Make sure that the Seat Post Knob is firmly engaged in one of the adjustment holes in the Seat Post (5). 1 Adjustment Holes 5 Hole 9 9.
HOW TO USE THE EXERCISE BIKE HOW TO ADJUST THE PEDALING RESISTANCE HOW TO ADJUST THE SEAT POST To increase the resistance of the pedals, turn the resistance knob clockwise; to decrease the resistance, turn the knob counterclockwise. IMPORTANT: Stop turning the knob when turning becomes difficult, or damage may result. For effective exercise, the seat should be at the proper height. As you pedal, there should be a slight bend in your knees when the pedals are in the lowest position.
FEATURES OF THE CONSOLE HOW TO USE THE MANUAL MODE 1. Turn on the console. To turn on the console, press any of the buttons or begin pedaling. The entire display and the pace guide will turn on for a moment; the console will then be ready for use. 2. Select the manual mode. When you turn on the console, the manual mode will be selected. If you have selected a pace workout, reselect the manual mode by pressing the Workout Select button repeatedly until zeros appear in the display. 3.
When you turn Indicators on the console, the scan mode will be selected automatically. One indicator will appear below the word Scan to show that the scan mode is selected, and a second indicator will show which information is currently displayed. Note: When the batteries are replaced, it may be necessary to reselect the desired unit of measurement. To reset the display, press the On/Reset button. To pause the console, stop pedaling. The time will flash if it is displayed.
HOW TO USE A PACE WORKOUT During the workout, the pace guide will prompt you to keep your pedaling speed near the target pace for the current segment. When the left indicator lights, increase your speed; when the right indicator lights, decrease your speed. When the center indicator lights, maintain your current speed. IMPORTANT: The pace guide is intended only to provide a goal. Make sure to pedal at a speed that is comfortable for you. 1. Turn on the console. See step 1 on page 12. 2.
MAINTENANCE AND TROUBLESHOOTING Turn the resistance knob to the lowest setting. Then, locate the Reed Switch (39). Turn the Crank (21) until a Magnet (38) is aligned with the Reed Switch. Loosen, but do not remove, the M5 x 15mm Screw (47). Inspect and tighten all parts of the exercise bike regularly. Replace any worn parts immediately. To clean the exercise bike, use a damp cloth and a small amount of mild detergent.
HOW TO ADJUST THE DRIVE BELT If you can feel the pedals slip while you are pedaling, even when the resistance is at the highest level, the drive belt may need to be adjusted. To adjust the drive belt, the pedals and the shields must be removed. 43 35 Use an adjustable wrench to remove the pedals. To remove the left pedal, turn the left pedal clockwise; to remove the right pedal, turn the right pedal counterclockwise.
EXERCISE GUIDELINES WARNING: Before beginning this Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of time. During the first few minutes of exercise, your body uses carbohydrate calories for energy. Only after the first few minutes of exercise does your body begin to use stored fat calories for energy. If your goal is to burn fat, adjust the intensity of your exercise until your heart rate is near the lowest number in your training zone.
PART LIST—Model No. WLEX31310.0 Key No. Qty. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 1 1 1 2 1 1 2 2 1 7 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Description Key No. Qty.
EXPLODED DRAWING—Model No. WLEX31310.
ORDERING REPLACEMENT PARTS To order replacement parts, please see the front cover of this manual.