www.weslo.com Model No. WLEL81914.0 Serial No. Write the serial number in the space above for reference. Serial Number Decal (under frame) ACTIVATE YOUR WARRANTY To register your product and activate your warranty today, go to www.wesloservice.com/ registration. CUSTOMER CARE For service at any time, go to www.wesloservice.com. Or call 1-866-699-3756 Mon.–Fri. 6 a.m.–6 p.m. MT Sat. 8 a.m.–12 p.m. MT Please do not contact the store.
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your elliptical before using your elliptical. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 1. It is the responsibility of the owner to ensure that all users of the elliptical are adequately informed of all precautions. 8.
STANDARD SERVICE PLANS all 4
BEFORE YOU BEGIN Thank you for selecting the revolutionary WESLO® MOMENTUM G 3.4 elliptical. The MOMENTUM G 3.4 elliptical provides an impressive selection of features designed to make your workouts at home more effective and enjoyable. reading this manual, please see the front cover of this manual. To help us assist you, note the product model number and serial number before contacting us. The model number and the location of the serial number decal are shown on the front cover of this manual.
PART IDENTIFICATION CHART Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it has been preassembled. Extra parts may be included.
ASSEMBLY • To hire an authorized service technician to assemble this product, call 1-800-445-2480. • In addition to the included tool(s), assembly requires the following tools: • Assembly requires two persons. one Phillips screwdriver • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until you finish assembly. one adjustable wrench • Left parts are marked “L” or “Left” and right parts are marked “R” or “Right.
3. Attach the Front Stabilizer (38) to the Frame (16) with two M8 x 65mm Carriage Bolts (57), two M8 Curved Washers (14), and two M8 Acorn Nuts (59) (only one side is shown); start both Carriage Bolts, and then tighten the Acorn Nuts. 3 38 16 59 4. While a second person holds the Upright (32) near the Frame (16), connect the Upright Wire (33) to the Reed Switch Wire (18).
5. Insert the excess wire and cable into the Frame (16). 5 Tip: Avoid pinching the wire and the cable. Slide the Upright (32) onto the Frame (16). Attach the Upright (32) with four M8 x 16mm Screws (15) and four M8 Curved Washers (14); start all the Screws, and then tighten them. Avoid pinching the wire and the cable 32 15 15 14 14 15 16 6. Connect the Resistance Cable (34) to the Lower Resistance Cable (24) in the following way: 6 Avoid pinching the cable A See drawing A.
7. Attach the Water Bottle Holder (9) to the Upright (32) with two M5 x 20mm Screws (12); start both Screws, and then tighten them. 7 9 32 12 8. Using a plastic bag to keep your hands clean, apply a generous amount of the included grease to the right axle on the Upright (32). 8 44 26 28 Next, orient an Upper Body Leg (44) as shown and slide it onto the right axle on the Upright (32). 27 Grease Attach the Upper Body Leg (44) with an M8 x 20mm Screw (28) and an M8 Large Washer (27).
9. Orient an Upper Body Arm (41) as shown and slide it onto the right Upper Body Leg (44). 9 Attach the Upper Body Arm (41) with two M8 x 40mm Bolts (60), two M8 Curved Washers (14) and two M8 Acorn Nuts (59); start both Bolts, and then tighten the Acorn Nuts. Attach the other Upper Body Arm (41) to the other Upper Body Leg (44) in the same way. 41 41 14 60 59 44 10. See drawing 10a. Identify the Right Pedal Arm (51) and orient it as shown.
11. Identify the Right Pedal (56) and orient it as shown. 11 63 54 Attach the Right Pedal (56) to the Right Pedal Arm (51) with three M6 x 35mm Bolts (63), six M6 Washers (62), and three M6 Locknuts (39). 46 62 Attach the Left Pedal (54) to the Left Pedal Arm (46) in the same way. 51 56 62 39 12. The Console (1) can use two AA batteries (not included); alkaline batteries are recommended. Do not use old and new batteries together or alkaline, standard, and rechargeable batteries together.
. While a second person holds the Console (1) near the Upright (32), connect the wire on the Console to the Upright Wire (33). 13 1 Avoid pinching the wires Tip: Avoid pinching the wires. Attach the Console (1) to the Upright (32) with four M5 x 10mm Screws (2); start all the Screws, and then tighten them. 33 32 2 14. Make sure that all parts of the elliptical are properly tightened. Extra parts may be included. Place a mat under the elliptical to protect the floor.
HOW TO USE THE ELLIPTICAL HOW TO MOVE THE ELLIPTICAL HOW TO USE THE ELLIPTICAL Due to the size and weight of the elliptical, moving it requires two persons. Stand in front of the elliptical, hold the upright, and place one foot against one of the front stabilizer caps. Pull on the upright and have a second person lift the rear stabilizer until the elliptical will roll on the front stabilizer caps. Carefully move the elliptical to the desired location, and then lower it to the floor.
HOW TO ADJUST THE PEDALING RESISTANCE To increase the resistance of the pedals, turn the resistance knob clockwise; to decrease the resistance, turn the knob counterclockwise. IMPORTANT: Stop turning the knob when turning becomes difficult, or damage may result.
CONSOLE DIAGRAM FEATURES OF THE CONSOLE The easy-to-use console features five modes that provide instant exercise feedback during your workouts. Scan (SCAN)—This mode displays the time, speed, distance, and calorie modes, for a few seconds each, in a repeating cycle. Time (TMR)—This mode displays the elapsed time. Note: If you set a time goal (see step 2 on page 17), this display will show the time remaining in your workout. Speed (SPD)—This mode displays your pedaling speed, in miles per hour.
HOW TO USE THE CONSOLE 3. Begin pedaling and follow your progress with the displays. Make sure that batteries (not included) are installed in the console (see assembly step 12 on page 12). If there is a sheet of plastic on the console, remove the plastic. Scan mode—To select the scan mode, press the MODE button repeatedly until the word SCAN appears in the display. 1. Turn on the console.
FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
MAINTENANCE AND TROUBLESHOOTING MAINTENANCE Locate the Reed Switch (18). Turn the Crank (3) until a Magnet (8) is aligned with the Reed Switch. Inspect and tighten all parts of the elliptical regularly. Replace any worn parts immediately. To clean the elliptical, use a damp cloth and a small amount of mild soap. IMPORTANT: To avoid damage to the console, keep liquids away from the console and keep the console out of direct sunlight.
HOW TO ADJUST THE DRIVE BELT If you can feel the pedals slip while you are pedaling, even when the resistance is at the highest level, the drive belt may need to be adjusted. To adjust the drive belt, first see assembly step 10 on page 11 and remove the Right Pedal Arm (51) from the right Upper Body Leg (44) and the right side of the Crank (3). Next, see the EXPLODED DRAWING on page 23.
EXERCISE GUIDELINES Aerobic Exercise—If your goal is to strengthen your cardiovascular system, you must perform aerobic exercise, which is activity that requires large amounts of oxygen for prolonged periods of time. For aerobic exercise, adjust the intensity of your exercise until your heart rate is near the highest number in your training zone. WARNING: Before beginning this or any exercise program, consult your physician.
PART LIST Key No. Qty. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 1 4 1 1 1 1 2 2 1 2 2 2 2 12 4 1 2 1 1 1 1 5 6 1 1 2 4 2 4 2 1 1 1 1 Model No. WLEL81914.0 R1115A Description Key No. Qty.
EXPLODED DRAWING Model No. WLEL81914.
ORDERING REPLACEMENT PARTS To order replacement parts, please see the front cover of this manual.
