Model No. WLTL35520 Serial No. USER'S MANUAL Serial Number Decal QUESTIONS? If you have questions, or if there are missing parts, we will guarantee complete satisfaction through direct assistance from our factory. TO AVOID DELAYS, PLEASE CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE. The trained technicians on our Customer Hot Line will provide immediate assistance, free of charge to you. CUSTOMER HOT LINE: 1-800-999-3756 Mon.-Fri., 6 a.m.-6 p.m.
TABLE OF CONTENTS IMPORTANT PRECAUTIONS ................................................................ BEFORE YOU BEGIN ...................................................................... ASSEMBLY ............................................................................... OPERATION AND ADJUSTMENT ............................................................. HOW TO FOLD AND MOVE THE TREADMILL .................................................. TROUBLESHOOTING .........................................
14. Never move the walking belt while the power is turned off. Do not operate the treadmill if the power cord or plug is damaged, or if the treadmill is not working properly. (See BEFORE YOU BEGIN on page 4 if the treadmill is not working properly.) kg) to raise, lower, or move the treadmill. 19. When folding or moving the treadmill, make sure that the storage latch is fu Ily closed. 15. Never start the treadmill while you are standing on the walking belt.
BEFORE YOU BEGIN Congratulations for selecting the new WESLO ®CADENCE 450 treadmill. The CADENCE 450 treadmill at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number of the treadmill is WLTL35520.
ASSEMBLY Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance.
Insert a Plastic Shim (103) into each side of the post on the right side of the Base (11). Next, orient the Right Upright (62) as shown, and insert it into the Base. Make sure that the Wire Harness (21) does not fall into the Right Upright. Be careful to avoid pinching the Wire Harness. Note: If necessary, tap the Right Upright with a rubber mallet until it is fully seated in the Base. If the Right Upright cannot be fully seated, remove the outer Plastic Shim and then insert the Right Upright.
. Place the Console Base (46) on the Right Handrail (47) and the Left Handrail (not shown). Attach the Console Base with four 1 1/4" Screws (105) (only two Screws are shown). Do not tighten the Screws yet. I 46 Insert the Wire Harness (21) through the two indicated plastic ties on the Console Base (46). Next, insert the Wire Harness up through the indicated opening in the Console Base. Make sure that the Console Cover (96) is securely attached to the Console Base. Refer to the inset drawing.
OPERATION AND ADJUSTMENT THE PERFORMANT LUBE TM WALKING BELT Your treadmill features a walking belt coated with PERFORMANT LUBE TM, a high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear. HOW TO PLUG IN THE POWER CORD an equipment-grounding conductor and a grounding plug.
CONSOLEDIAGRAM FA_ \ \ CALORIES HME SPEED DISTANCE \ plastic on the console, remove it. Key-- ing a few steps backward until the key is pulled from the console. If the key is not pulled from the console, adjust the position of the clip. Then, reinsert the key fully into the console. CAUTION: Before operating the console, read the following precautions. • Do not stand on the walking belt when turning on the power. Follow the steps below to operate the console.
To stop the walking belt, press the Stop button. The Time display will begin to flash. will appear in the Calories/Fat Calories/Pulse display. Press the Speed :£ button to change the unit of measurement. When the desired unit of mea- Note: During the first few minutes that the treadmill is used, inspect the alignment of the walking belt and align it if necessary (see page 14). surement is selected, remove the key and then reinsert it.
THE INFORMATION MODE The console features an information mode that keeps track of the total number of hours that the treadmill has been operated and the total number of miles that the walking belt has moved. The information mode also allows you to switch the console from miles per hour to kilometers per hour. To select the information mode, hold down the Stop button, insert the key into the console, and continue to hold the Stop button for a moment.
HOW TO FOLD AND MOVE THE TREADMILL HOW TO FOLD THE TREADMILL FOR STORAGE Before folding the treadmill, unplug the power cord. CAUTION: You must be able to safely lift 45 pounds (20 kg) in order to raise, lower, or move the treadmill. . \ Hold the treadmill with your hands in the locations shown at the right. To decrease the possibility of injury, bend your legs and keep your back straight. As you raise the treadmill, make sure to lift with your legs rather than your back.
TROUBLESHOOTING Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department tollfree at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). PROBLEM: The power does not turn on SOLUTION: a.
PROBLEM: The walking belt slows when walked on SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 8. b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn both rear roller adjustment bolts counterclockwise, 1/4 of a turn.
CONDITIONING GUIDELINES ergy. Only after the first few minutes does begin to use stored fat calories for energy. is to burn fat, adjust the speed and incline mill until your heart rate is near the lowest your training zone. Before beginning this or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
PART IDENTIFICATION CHART Remove this chart and use it to identify small parts during assembly. Save this chart and the EXPLODED DRAWING/PART LIST for future reference. 4:\\\\\\\\\D Crossbar Screw (53)-2 (_ 3/4" Screw (13)-6 3/4" Tek Screw (102)-4 1/2" Silver Screw (97)-2 1" Bolt (8)-12 Wheel Nut (38)-2 1 1/4" Screw (105)-4 Silver Ground Screw (104)-1 Washer (57)-4 Wheel Bolt (36)-2 Star Washer (9)-6 (May be an internal Star Washer)
PART LIST--Model Key No. Qty. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20* 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 1 1 2 1 1 1 1 12 10 1 1 1 13 1 1 7 3 1 1 1 1 4 1 1 9 1 1 1 1 1 2 1 7 1 10 2 2 4 5 4 2 1 1 1 1 1 1 4 2 1 1 2 2 1 1 1 4 No.
m X !- 0 25 m 10 46 90 13 24 41 13_ 14 12 95 Z 27 97 13 _ I 99 98 48 45 44 103 o 71 49 Z o 67 101 68 \ 25_ 31 86 32 4 48-._ 36 37 48 I-C_ 57 66 84@ 77 74 3 0 .... 82 39 83 83 \ 103 33 0 0 1',3
ORDERING REPLACEMENT PARTS To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
