Assembly Instruction

ManualsBrandsWest Elm ManualsAccessoriesWest Elm Faceted Mirror Semi Flush Fixture

Important Safety Instructions:

These instructions are provided for your safety. It is important that they are read carefully and completely

before installing the chandelier.

We strongly recommend that a professional electrician install all direct wire  xtures.

This  xture has been rated for up to 60-watt TYPE A bulbs (not included). To avoid the risk of  re, do not

exceed the recommended wattage.

Pre-assembly:

Remove all parts and hardware from box along with any plastic protective packaging. Do not discard any

contents until after assembly is complete to avoid accidentally discarding small parts or hardware.

For your safety and convenience, assembly by two people is recommended.

WARNING: This lighting  xture contains lead, a chemical known to the State of California to cause cancer,

birth defects and other reproductive harm. Wash hands after installing, handling, cleaning or otherwise

touching this light  xture

Parts Enclosed:

(1) Mounting plate (D)

(1) Canopy (F)

(1) Canopy screws (E)

(1) Socket (H)

(1) Socket Ring (I)

(1) Shade (G)

Hardware Included:

•(2) Mounting screws (C)-1pc extra

•(1) Green ground screws (B)

•(3) Plastic wire connectors (A)

• (1) Metal Plate (H)

To Assemble:

SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER.

Carefully unpack all  xture parts and hardware and lay out on a clear workspace.

1.Carefully inspect the Flush's  xture wires. The NEUTRAL FIXTURE WIRE is marked “N”. The HOT FIXTURE

WIRE is marked “L”. The yellow-green or bare wire is the GROUND WIRE.

2.Attach the GROUND WIRE from the  xture to the GROUND JUNCTION BOX WIRE from the outlet (usually

green or bare wire). Fasten each together with a plastic wire connector (A) and wrap the connection with

electrical tape. Be sure that no wire strands are exposed. If your outlet box DOES NOT have a GROUND

WIRE, be sure to insert the green ground screw (B) into the Mounting plate (D) facing DOWN, and wrap

the  xture's bare ground wire around the ground screw. IT IS IMPERATIVE THAT THE OUTLET BOX IN YOUR

HOME BE PROPERLY GROUNDED.

Summary of content (6 pages)

PAGE 1
Important Safety Instructions: These instructions are provided for your safety. It is important that they are read carefully and completely before installing the chandelier. We strongly recommend that a professional electrician install all direct wire fixtures. This fixture has been rated for up to 60-watt TYPE A bulbs (not included). To avoid the risk of fire, do not exceed the recommended wattage. Pre-assembly: Remove all parts and hardware from box along with any plastic protective packaging.
PAGE 2
Connect the NEUTRAL FIXTURE WIRE to the NEUTRAL JUNCTION BOX WIRE (white) or marked “N”. Fasten each together with a plastic wire connector (A) and wrap the connection with electrical tape. Be sure no wire strands are exposed. Connect the HOT FIXTURE WIRE to the HOT JUNCTION BOX WIRE ( black) or marked “N”. Fasten each together with a plastic wire connector (A) and wrap the connection with electrical tape. Be sure no wire strands are exposed.
PAGE 3
Importantes Consignes de Sécurité: Ces instructions sont fournies pour votre sécurité. Il est important que vous les lisiez en entier et en détails avant de commencer l’installation de ce luminaire. Nous recommandons vivement l’installation des câbles électriques par un électricien professionnel. Ce luminaire a été évalué pour utilisation avec des ampoules de TYPE A de 60 Watts (non fournies). Pour éviter tout risque d’incendie, ne dépasser pas le voltage maximum recommandé.
PAGE 4
(B) dans la plaque de fixation (D) face VERS LE BAS, puis enroulez le fil de terre non gainé du luminaire autour de la vis de terre. IL EST IMPERATIF QUE LA BOITE A PRISES DE VOTRE DOMICILE SOIT BIEN MISE A TERRE. Connectez le FIL NEUTRE DU LUMINAIRE à la BOITE DE JONCTION NEUTRE (blanche ou marqué d’un « N »). Attachez ensemble avec un embout de connexion en plastique (A) puis enroulez du ruban adhésif électrique autour du point de connexion. Vérifiez qu'aucun brin de fil ne dépasse.
PAGE 5
Intstrucciones de Seguridad Importante: . Se proporcionan estas instrucciones para su seguridad. Es importante que las lea de manera detallada y completa antes de ensamblar la unidad de iluminación. . Se recomienda la instalacion por parte de un electricista profesional para todas las unidades de cable. Esta unidad ha sido aprobada para hasta (1) bombillos incandescente standard TIPO A 60-vatios maximo (no inlcuidos) o bombillos de 13 vatios compacto fluorescente (no incluidos).
PAGE 6
unidad alrededor del tornillo tierra (c). ES MUY IMPORTANTE QUE LA CAJA DE CONECCION EN SU CASA ESTE CORRECTAMENTE ATERRADO! Conecte el CABLE NEUTRAL DE LA UNIDAD al CABLE NEUTRAL DE LA CAJA DE CONECCION (blanco) o marcado con la letra “N”. Conecte ambos con un Conector de Cable (a) y cubra la coneccion con cinta electrica. Asegurese que no quede cable expuesto. Conecte el CABLE CALIENTE DE LA UNIDAD al CABLE CALIENTE DE LA CAJA DE CONECCION (negro).