Assembly Instruction

ManualsBrandsWest Elm ManualsAccessoriesWest Elm Finn Chandelier

Important Safety Instructions:

•These instructions are provided for your safety. It is very important that they are read carefully and com

pletely before beginning the installation of this lighting  xture.

•THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODES BY A

PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS IN

VOLVED.

•We strongly recommend that a professional electrician install all direct wire  xtures.

•This  xture has been rated for up to (3) 60-Watt maximum Type A standard incandescent light bulbs (not

included) or 13-watt compact  uorescent bulb (not included). To avoid the risk of  re, do not exceed the

recommended lamp wattage.

•The lighting  xture is meant for indoor use. It must be connected only to 3-wire, single-phase electrical

supply systems (provided with Ground wire or equivalent protection system).

• Save this instruction.

WARNING:

• To reduce the risk of  re, electrical shock or personal injury, always turn o light  xture and unplug, allow

ing it to cool prior to replacing light bulb.

• Do not touch bulb when  xture is turned on.

• Do not look directly at lit bulb. Keep  ammable materials away from lit bulb.

SHUT OFF ALL THE MAIN ELECTRICAL SUPPLY FROM THE FUSE BOX / CIRCUIT BREAKER

Pre-assembly:

•Remove all parts and hardware from box along with any plastic protective packaging. Do not discard any

contents until after assembly is complete to avoid accidentally discarding small parts or hardware.

PARTS INCLUDED: HARDWARE ENCLOSED: TOOLS REQUIRED (not included)

(1) Mounting Plate (A) (3) Plastic wire connectors (a) 1. Electrical tape

(1) Canopy (B) (2) Mounting screws (b) 2. Screwdriver

(1) 6” Tube (C) (1) Green ground screw (c) 3. Two peoples recommended

(3) 12” Tube (D) (4) Flat head screws (d)

(1) Light Fixture (E)

(3) Sockets (F)

(3) Shades (G)

(3) Shade Cups (H)

(3) Shade Rings (I)

Summary of content (6 pages)

PAGE 1
Important Safety Instructions: •These instructions are provided for your safety. It is very important that they are read carefully and com pletely before beginning the installation of this lighting fixture. •THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODES BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS IN VOLVED. •We strongly recommend that a professional electrician install all direct wire fixtures.
PAGE 2
To Assemble: 1. Carefully unpack all fixture parts and hardware and lay them on a clean workspace. 2. Determine the number of (D) tubes required to achieve thedesired fixture hanging length. Attach the 12” Tubes (D) onto the Lighting Fixture (E) by turning the 12” Tubes (D) in a clockwise direction. 3. Attach the 6” Tube (C) onto the end of 12” Tube (D) by turning the 6” Tube (C) in a clockwise direction. 4.
PAGE 3
Importantes Consignes de Sécurité: • Ces instructions sont fournies pour votre sécurité. Il est important que vous les lisiez en entier et en détails avant de commencer l’assemblage. • CET ARTICLE DOIT ETRE INSTALLE PAR UNE PERSONNE FAMILIERE AVEC LA CONSTRUCTION ET L’UTILISATION DE CE TYPE DE PRODUIT ET LES RISQUES ENCOURUS ET QUI PEUT L’INSTALLER EN SUIVANT BIEN LES REGULATIONS RELATIVES A CE TYPE DE PRODUIT.
PAGE 4
Pour l’assemblage: 1. Sortez délicatement toutes les pièces et le matériel des cartons d’emballage et étalez-les sur une surface de travail propre. 2. Déterminer le nombre de (D) les tubes nécessaires pour atteindre longueur du luminaire thedesired pendaison. Fixez le 12 “Tubes (D) sur l’appareil d’éclairage (E) en tournant le 12” Tubes (D) dans le sens horaire.3. Attachez les tubes de 6” (C) sur les extrémités des tubes de 12” (D) en tournant les tubes de 6” (C) dans le sens des aiguilles d’une montre. 4.
PAGE 5
Intstrucciones de Seguridad Importante: . Se proporcionan estas instrucciones para su seguridad. Es importante que las lea de manera detallada y completa antes de ensamblar la unidad de iluminación. . ESTE PRODUCTO DEBE SER INSTALADO DE ACUERDO A TODOS LOS CODIGOS DE INSTALACION APLICABLES POR UNA PERSONA FAMILIARIZADA CON LA CONSTRUCCION Y OPERACION DEL PRODUCTO Y LOS PELIGROS RELACIONADOS. . Se recomienda la instalacion por parte de un electricista profesional para todas las unidades de cable.
PAGE 6
Instrucciones de Ensamblaje: 1.De manera cuidadosa desempaque todas las partes y piezas y coloquelas en un lugar de trabajo despe jado. 2. Determinar el número de (D) los tubos necesarios para alcanzar la longitud accesorio thedesired colgan do. Conecte el 12 “Tubos (D) en el accesorio de iluminación (E) en el sentido de los 12” Tubos (D) en el sen tido de las agujas del reloj. 3.Inspeccione cuidadosamente los cables de la unidad de iluminacion. El CABLE NEUTRAL DE LA UNIDAD está marcado con la letra “N”.