Assembly Instruction

Important Safety Instructions:
These instructions are provided for your safety. It is important that they are read carefully and completely before installing the
chandelier.
We strongly recommend that a professional electrician install all direct wire  xtures.
This  xture has been rated for up to 3x60-watt TYPE A bulbs (not included). To avoid the risk of  re, do not exceed the
recommended wattage.
Pre-assembly:
Remove all parts and hardware from box along with any plastic protective packaging. Do not discard any contents until after
assembly is complete to avoid accidentally discarding small parts or hardware.
For your safety and convenience, assembly by two people is recommended.
WARNING: This lighting  xture contains lead, a chemical known to the State of California to cause cancer, birth defects and other
reproductive harm. Wash hands after installing, handling, cleaning or otherwise touching this light  xture
Parts Enclosed:
(1) Mounting plate (D)
(1) Canopy (E)
(2) Pole (J)
(2) Pole (H)
(2) Mirror Plate (I)
(2) Mirror Plate (J)
(1) Shade Frame(K)
(2) Thread Rod (L)
(1) Ground Ring (P)
(4) Clip (T)
Hardware Included:
•(3) Plastic wire connectors (A)
•(1) Green ground screws (B)
•(2) Mounting screws (C)
•(4) Canopy screws (F)
•(4) Pole (M)
•(3) Washer (O)
•(2) Hex Nut (Q)
•(1) Iron Wrench ( R)
•(1) Iron Key (S)
To install you will need:
•Electrical tape
•Screwdriver
•2 people recommended
To Assemble:
1. SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER.
2. Carefully unpack all  xture parts and hardware and lay them out onto a clean smooth workspace.
3. Uncrew screws on top of light  xture 1 turn to allow the clip to rotate 90˚. Rotate the clip (T) clockwise 90˚ and place the Glass
Plate (I) into the Shade Frame (K) and rotate the Clip (T) to lock the glass into place. Re-tighten all screws.
4. Inset the Mirror Plate (J) into the Shade Frame(K)
5. Screw the Pole (H) onto the Threaded Rod (L)
6. Screw the Pole (J) onto the Pole (H)
7. Align the Canopy (E) hole with the Pole (J) and align the Canopy (E) onto the Pole (J).
8. Apply the Washer (O) and Ground Wire Ring (P) onto the Pole (J) on the right side as shown in the image on page 7.
9. Screw the Hex Nut (Q) onto the Pole (J) tighten by supplied wrench (R)
10. Apply the Washer (O) onto the Pole (J) on the Left side.
11. Screw the Hex Nut (Q) onto the Pole (J) tighten by supplied Wrench (R)
12. With help holding the  xture in place. Carefully inspect the chandelier's  xture wires. The NEUTRAL FIXTURE WIRE is marked “N”.
The HOT FIXTURE WIRE is marked “L”. The yellow-green or bare wire is the GROUND WIRE.
13. Attach the GROUND WIRE from the  xture to the GROUND JUNCTION BOX WIRE from the outlet (usually green or bare wire).
Fasten each together with a plastic wire connector (A) and wrap the connection with electrical tape. Be sure that no wire strands
are exposed. If your outlet box DOES NOT have a GROUND WIRE, be sure to insert the green ground screw (B) into the Mounting
plate (F) facing DOWN, and wrap the  xture's bare ground wire around the ground screw. IT IS IMPERATIVE THAT THE OUTLET
BOX IN YOUR HOME BE PROPERLY GROUNDED.
14. Connect the NEUTRAL FIXTURE WIRE to the NEUTRAL JUNCTION BOX WIRE ( white). Fasten each together with a plastic wire
connector (A) and wrap the connection with electrical tape. Be sure no wire strands are exposed.
15. Connect the HOT FIXTURE WIRE to the HOT JUNCTION BOX WIRE ( black). Fasten each together with a plastic wire connector (A)
and wrap the connection with electrical tape. Be sure no wire strands are exposed. DO NOT REVERSE THE HOT AND NEUTRAL
CONNECTIONS OR SAFETY WILL BE COMPROMISED.