User's Manual

ManualsBrandsWestell ManualsElectronicsDual Band Bidirectional Amplifer

MORPH MANUAL

WORD FORMAT

Table of Contents

Product Registration/Certification Information................1

Safety Guidelines.....................................................…..1

Product Information....................................................…2

Pin-Out Chart..............................................…..2

LED Indicators.............................................…..2

Mechanical Outline Drawing..........................…3

Installation..............................................................…….4

Important Safety Information....................................…..5

Amplifier Adjustment.................................................….6-9

Troubleshooting........................................................….10

Product Warranty.....................................................…..11

Product Certification/Registration Information

The serial number may be found on the label on the rear panel of the unit. For your convenience, note

this number below. Retain this manual, along with proof of purchase, to serve as a permanent record of

your purchase for future reference or in the event of theft.

Safety Guidelines

The general safety information in this guideline applies to both operating and service personnel. Specific warnings and

cautions will be found in other parts of this manual where they apply, but may not appear in this summary. Failure to comply

with these precautions or specific warnings elsewhere in the manual violates safety standards of design, manufacture, and

intended use of equipment. Cellular Specialties, Inc. assumes no liability for the customer’s failure to comply with these

requirements.

Grounding

This amplifier system is designed to operate from 120 Vac @ 1.3A maxpower and should always be operated with the

ground wire properly connected. Do not remove or otherwise alter the grounding lug on the power cord.

Explosive Atmospheres

This product has an integral circuit breaker, which may cause an electrical flash if the breaker should reset. To avoid

explosion or fire, do not operate this product in the presence of flammable gases or fumes.

Summary of content (12 pages)

PAGE 1
MORPH MANUAL WORD FORMAT Table of Contents Product Registration/Certification Information................1 Safety Guidelines.....................................................…..1 Product Information....................................................…2 Pin-Out Chart..............................................…..2 LED Indicators.............................................…..2 Mechanical Outline Drawing..........................…3 Installation...........................................................
PAGE 2
Lightning Danger Do not install or make adjustments to this unit during an electrical storm. No User Serviceable Parts Inside HAZARDOUS VOLTAGES ARE PRESENT WHEN THE COVER IS REMOVED. Opening the chassis will void your warranty. If you suspect a malfunction with this product, call your dealer or the Cellular Specialties Support Line at (603) 626-6677. DISCLAIMER: All information and statements contained herein are accurate to the best of the knowledge of Cellular Specialties, Inc.
PAGE 3
LCD Model Mechanical Drawing O I DIS PLA Y
PAGE 4
Installation CSI recommends that all BDA installations be coordinated through the local wireless provider. Example: Standard Single Internal Antenna System Design Optional Accessories Accessories are available directly from Cellular Specialties, Inc. or any of CSI’s distributors. • Outside High Gain Yagi Antennas PCS – model number (CSI-AY/1.85-1.99/10) SMR and Cellular – model number (CSI-AY/806-960/11) and (CSI-AY/806-960/14) • Inside Omni directional Antennas PCS – model number (CSI-AS/1.85-1.
PAGE 5
Important Installation Notes • A high degree of isolation must be afforded to prevent any re-generative feedback in the system. Feedback of this nature causes the amplifier to emit a continuous signal of maximum amplitude and could, in some cases, interfere with normal operation of the cell site. The minimum required isolation of 80 dB can usually be obtained by mounting the outside antenna away from the edges of the roof. The use of window mounts or other non-rooftop mountings should be avoided.
PAGE 6
Performance Adjustment The menu system can be navigated with five buttons: UP, DOWN, EDIT, SAVE, and MENU. Feedback is given to the operator through the LCD panel. Generally speaking, the MENU button is used to switch among various menus available on the LCD panel without altering the contents of non-volatile memory. The EDIT button is used to alter values that are present, when possible. The UP and DOWN buttons permit choice among various options available within a given menu.
PAGE 7
the fans were set and the speed at which they were found to operate; and Overheat errors, which are catalogued when the temperature of the board runs too high despite the fans running at full speed. Pressing UP and DOWN permits the user to examine the number of errors logged in each category. Pressing EDIT clears the counters of all errors. Pressing SAVE has no effect. Pressing MENU sends the user to the Peak Power Menu. Peak Power Menu.
PAGE 8
showing the current maximum uplink gain. Upon entering this menu, the screen will resemble this: The user can move on to the next menu by pressing the MENU key, or change the value by pressing EDIT and scrolling to the desired value with the UP and DOWN keys.
PAGE 9
As an example, let’s say the user wants to change the name of the amplifier on the network from “CEL” to “PCS”. She gets to the menu by pressing MENU until this screen appears: Then, to inform the amplifier that she wants to change the name, she presses EDIT, and this screen appears: To change ‘A’ to ‘P’, she needs to press the UP key fifteen times. (Alternatively, she could hold the UP key down until the proper letter appears.
PAGE 10
As usual, the user can move past this menu by pressing MENU, which would return the user to the Default Menu above. Pressing EDIT, however, changes the screen to resemble this: The user can then use the UP and DOWN arrows to scroll to a desired address. Pressing SAVE locks the selected address in non-volatile memory and returns the user to the Default Menu.
PAGE 11
Troubleshooting All cables should be carefully checked for “shorts” and “opens”. The rooftop antenna, if directional, should be checked for proper alignment along the calculated compass heading. Typically, the directional antenna should be aimed at the same site that your handset uses in the area where the outside antenna is placed. If cables and alignment are acceptable, it may be necessary to use a spectrum analyzer to examine the signal environment in which the BDA is operating.
PAGE 12
One Year Limited Warranty Seller warrants that its products are transferred rightfully and with good title; that its products are free from any lawful security interest or other lien or encumbrance unknown to Buyer; and that for a period of one year from the date of installation or fifteen months from the date of original shipment, whichever period expires first, such products will be free from defects in material and workmanship which arise under proper and normal use and service.