Installation manual

11 A·1 DIESEL ENGINE SPECIFICATIONS
ENGINE SPECIFICATIONS
Engine Type Diesel, four-cycle, one cylinder, raw water cooled,
vertical, in-line overhead valve mechanism
Aspiration Naturally aspirated
Governor Mechanical, centrifugal type
Combustion System Direct injected
Bore and Stroke 3.74 in. x 2.91 in. (95.0 mm x 74.0 mm)
Piston Displacement 31.95 cu. in. (524.0 cm')
Crankshaft Clockwise, when viewed from the front
Direction of Rotation (raw water pump end)
Compression Ratio 20:1
Maximum Torque 21.3 ftIIbs (2.9 kg-m)
at (2400 rpm)
Manual Starting System Hand-crank, with automatic
decompression device
Engine Stop Manual type
Dimensions
NOTE: An inserted standard
crank handle increases the
width by 4.5 in. (115 mm)
Dry Weight
Height: 21.0 in (532 mm)
Width: 21.3 in (540 mm)
Length: 23.8 in (603 mm)
238 Ibs (108 kg)
Max. Angle of I nstallation Not to exceed 1 0°
Max. Angle of Operation Not to exceed 15° in all directions
TUNE-UP SPECIFICATIONS
Compression Pressure
Valve Seat Angle
Valve Clearance
(engine cold)
Engine liming
Injector Pressure
Engine Speed
Fuel System
Fuel
Fuel
Uft Pump
Fuel Injection Pump
Fuel I njector
Fuel Injection liming
Injector Pressure
Fuel Consumption
(full load)
Fuel Riter
Fuel Supply
and Retum Lines
Air Row
(engine combustion)
478.5 psi (33.6 kg/cm') standard
435.0 psi (30.6 kg/cm') minimum
Intake 45°; Exhaust 45°
Intake 0.008 in. (0.2 mm)
Exhaust O.OOS in. (0.2 mm)
60.0 mm BlDC static
2537 psi (178.3 kg/cm')
Idle: 1000 -1200 rpm
Cruise: 2000 - 2500 rpm
Maximum: 2900 - 3000 rpm
FUEL SYSTEM
Open flow, self-priming, seH-bleeding
No.2 diesel oil, cetane rating of 45 or higher
Mechanical 1.6 ft. (0.5 m) lift max.
Bosch type
Direct Injection
60 mm BTDC static
2537.5 psi (178.4 kg/cm')
0.46 U.S. gaL/hr. (1.76Iiterlhr.)
Primary replaceable filter
1/4 in. (6.35 mm) 1.0. minimum
5/16 in. (7.94 mm) 1.0. maximum
27.7 cfm (0.78 cmm)
LUBRICATION SYSTEM
Lubrication System
Sump Capacity
Operating Oil Pressure
(engine hot)
Oil Grade
Oil Riter
Forced lubrication by gear-driven pump
1.7 qts. (1.6 liter)
25.&-56.9 psi (1.8-4.0 kg/cm')
API specification CF or CG-4
SAE 30, 10W-30, 15W-40
Full-flow, paper element, spin-on type
COOLING SYSTEM
Cooling System
Operating Temperature
Raw Water Pump
Raw Water Row,
at 3600 rpm
Raw Water Connection
Raw water-cooled block,
thermostatically controlled
13D-150°F (55-66°C)
Positive displacement, neoprene impeller,
gear-driven, seH-priming
7.399-8.456 gpm (7-8lpm)
112 in. (12.7 mm) 1.0.
EXHAUST SYSTEM
Emission Control Systems Meets U.S.C.G. Regulation 33 CFR 183
Exhaust ManifoldlElbow Cast aluminum, raw water cooled
Exhaust Elbow Connection 1-112 in. (38.1 mm) 1.0.
ELECTRICAL SYSTEM
Electrical System
Battery Charging
Alternator
Starting Motor
Cold Cranking Amps
General
Gear Ratio (optional)
Propeller
Propeller used must allow
the engine to reach its rated
rpm at full open throttle in
forward gear, underway
lubricating Ruid
Transmission Sump
Capacity
Propeller Shaft
Direction of Rotation
12 volts DC, negative ground,
circuit breaker protected
30 amp, 12 volts, belt-driven,
with solid state intemal regulator
12 volt solenoid, actuated shift
60 amps@66°F (19°C)
TRANSMISSION
HURTH HBW 40 Standard Transmission, case-
hardened helical gears, with a servo-operated
multiple disc clutch
2.05:1
14 Dx8 Ptwoblade-RH
140 x 6 P three blade - RH
ATF- type A or DEXTRON - /I or 11/
0.37 qts (0.35 liters)
Right hand-standard transmission
Engines & Generators
6