6643-2250 Lynx WeOS L106-F2G/L206-F2G Industrial Ethernet 6-port Switch www.westermo.
License Information This device contains public available software which is under the GPL license. For more information see legal.pdf included with all firmware releases. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. http://www.openssl.org Legal information The contents of this document are provided “as is”.
Safety ! Before installation: Read this manual completely and gather all information on the unit. Make sure that you understand it fully. Check that your application does not exceed the safe operating specifications for this unit. This unit should only be installed by qualified personnel. This unit should be built-in to an apparatus cabinet, or similar, where access is restricted to service personnel only.
Note. Fibre Optic Handling Fibre optic equipment needs special treatment. It is very sensitive to dust and dirt. If the fibre will be disconnected from the unit the protective hood on the transmitter/receiver must be connected. The protective hood must be kept on during transportation. The fibre optic cable must also be handled the same way.
Declaration of Conformity Westermo Teleindustri AB Declaration of conformity The manufacturer Westermo Teleindustri AB SE-640 40 Stora Sundby, Sweden Herewith declares that the product(s) Type of product Model 1 Industrial Ethernet 6-port Switch Lynx L*06-F2G* is in conformity with the following EC directive(s).
Type tests and environmental conditions Environmental phenomena ESD Basic standard EN 61000-4-2 Description Enclosure Fast transients EN 61000-4-4 Surge EN 61000-4-5 Power port Signal ports Earth port Power port Signal ports Power frequency magnetic field Pulsed magnetic field Radiated RF immunity EN 61000-4-8 EN 61000-4-9 EN 61000-4-3 Enclosure Enclosure Enclosure Conducted RF immunity EN 61000-4-6 Radiated RF emission Conducted RF emission EN 55022 FCC Part 15 EN 55022 Power port Signal por
Description L106-F2G/L206-F2G is an Industrial switch made for harsh enviroments. The switch can be used in either 100 Mbit or Gigabit networks due to our multi-rate SFP solution. L106-F2G/L206-F2G can also be used together with our previous Lynx-series of switches. Our unique FRNT (Fast Recovery of Network Topology) technology is the fastest protocol on the market to re-configure a network in the event of any link or hardware failure.
Interface specifications Power Operating voltage Rated current Rated frequency Inrush current, I2t Startup current* Polarity Redundant power input Isolation to Connection Connector size Shielded cable Rated: 24 to 48 VDC Operating: 19 to 60 VDC 180 mA (330 mA) @ 24 VDC (with 500 mA USB load) 90 mA (170 mA) @ 48 VDC (with 500 mA USB load) DC 22.7·10-3 A2s @ 48 VDC 2 x Rated current Reverse polarity protected Yes All other Detachable screw terminal 0.2 – 2.
I/O / Relay output Maximum voltage/current Contact resistance Isolation to Connection Connector size 60 VDC / 80 mA Max 30 Ω All other Detachable screw terminal 0.2 – 2.5 mm2 (AWG 24 – 12) I/O / Digital input Maximum voltage/load current 60 VDC / 2 mA Voltage levels Logic one: >12V Logic zero: <1V Isolation to All other Connection Detachable screw terminal Connector size 0.2 – 2.5 mm2 (AWG 24 – 12) USB Electrical specification USB 2.
Location of interface ports and LED’s LED Indicators (for details see page 12) Power connection (for details see page 11) USB Position Direction No. 1 Out Description No. 2 In/Out D– No. 3 In/Out D+ No. 4 Out Shield In/Out VBUS GND Connected to protective earth SFP transceivers (for details see page 9) Ethernet connection TX (4 ports) Position Signale Direction Description No.1 TD+ In/Out Transmitted/Received data No. 2 TD– In/Out Transmitted/Received data No.
Power connection 4-position Product marking Direction Description No. 1 +DC1 Input Supply voltage input DC1 No. 2 +DC2 Input Supply voltage input DC2 No. 3 -COM Input Common No. 4 -COM Input Common 1 2 3 4 Lynx supports redundant power connection. The positive inputs are +DC1 and +DC2, the negative input for both supplies are –COM. Connect the primary voltage (e.g. +24 VDC) to the +DC1 pin and return to one of the –COM pins on the power input.
LED indicators LED Status Description ON OFF Unit has no power. GREEN All OK, no alarm condition. RED Alarm condition, or until unit has started up. (Alarm conditions are configurable, see ''WeOS Management Guide''). BLINK Location indicator ("Here I am!"). Activated when connected to IPConfig Tool, or upon request from Web or CLI. OFF Unit has no power. GREEN Power OK on DC1. RED Power failure on +DC1. OFF Unit has no power. GREEN Power OK on DC2. RED Power failure on +DC2.
Mounting This unit should be mounted on 35 mm DIN-rail, which is horizontally mounted inside an apparatus cabinet or similar. It is recommended that the DIN-rail is connected to ground. Snap on mounting, see figure. Mounting Lynx with integrated DIN-clip: Removal Removing Lynx with integrated DIN-clip: Press down the support at the back of the unit using a screwdriver. See figure. Cooling This unit uses convection cooling. To avoid obstructing the airflow around the unit, use the following spacing rules.
Getting Started This product runs Westermo Operating System (WeOS) which provides several management tools that can be used for configuration of the unit. • IPConfig tool This is a custom Westermo tool used for discovery of attached Westermo units. • Web Configuration of the unit using the web browser. • CLI Configuration of the unit via the Command Line Interface.
Referring documents Type Management Guide Description Westermo OS management guide Document number 6101-3201 Factory default on L106-F2G and L206-F2G It is possible to set the unit to factory default settings by using two straight standard Ethernet RJ-45 cables. 1. Power off the switch and disconnect all Ethernet cables (copper and fibre). 2. Connect one Ethernet cable between Ethernet ports 3 and 6, and the other between Ethernet ports 4 and 5.
Westermo • SE-640 40 Stora Sundby, Sweden Tel +46 16 42 80 00 Fax +46 16 42 80 01 E-mail: info@westermo.com www.westermo.com Sales Units Westermo Data Communications China sales.cn@westermo.com www.cn.westermo.com France infos@westermo.fr www.westermo.fr Germany info@westermo.de www.westermo.de North America info@westermo.com www.westermo.com Singapore sales@westermo.com.sg www.westermo.com Sweden info.sverige@westermo.se www.westermo.se United Kingdom sales@westermo.co.uk www.westermo.co.
