Datasheet

US 7,099,934 B1
17
word, the veri?cation of the new password and the veri?
cation of the existing password in the case of changing the
ADMN password.
Regarding “SET SHOW [usemame] [ON|OFF]”, the SET
SHOW command is used to enable or disable SHOW
command access for a username. The SET SHOW command
can be entered with no parameters, with a single parameter
(which is a usemame) or with two parameters (which are
usemame followed by “on” or “o?‘” to indicate the SHOW
command is to be enabled or disabled). If a parameter is not
speci?ed, a user is prompted ?rst for a user name with the
“Usemame:” message followed by a prompt for the “on” or
“o?‘” speci?cation with the “Specify ON or OFF:” message.
If a user does not specify a valid usemame in response to the
“Usemame:” prompt, the command aborts with the follow
ing message: “Sorry, a usemame a user has entered is NOT
valid!”. If a user enters a single parameter, the “Specify ON
or OFF:” prompt occurs. If a user speci?es both a usemame
and “on”/“o?°’ parameters there is no prompting. The appro
priate error message is issued and the command aborted if a
usemame is invalid, regardless if the “on”/“o?°’ value is
speci?ed as a parameter on the command line or is entered
in response to a prompt. If the command completes suc
cessfully, the following message is displayed: “Show com
mand enabled/disabled for USERNAME”. In this message,
USERNAME is replaced by the speci?ed usemame and
either enabled or disabled is displayed depending on the
action taken.
Regarding “SET SCREEN (NOCONFIRM|CONFIRM]”,
the SET SCREEN command is used to enable or disable a
con?rmation message when using the power manager full
screen interface. When the CONFIRM option is set a user is
prompted with an “Are the sure? (Y/“N”)” message when
making changes via the SHOW command screen. When the
NOCONFIRM option is set changes are made immediately.
This command changes the con?rm option on all boards in
a power manager chain.
The following SET commands are used to set parameters
pertaining to SNMP traps that can be generated by power
managers. Not all power manager hardware support all
SNMP traps. Some of these commands use Board Name as
a parameter. The Board Name is the name speci?ed in the
Page ?eld of the SHOW command full screen interface. In
addition to specifying the mnemonic name from the SHOW
command page ?eld, a user may specify an absolute Board
Name by preceding the Board Name with a period (“.”).
Appending the power manager Board letter (e.g., “A” for the
?rst board, “B” for the second board, etc. to the leading
period creates the absolute Board Names. For example, the
third power manager Board in the chain of boards would
have an absolute Board Name of “.C”. If the chain of power
manager Boards is altered for any reason, the absolute Board
Names change. For example, if the second board in the chain
is removed (perhaps it fails), and what used to be the third
board is now connected to the ?rst board (it is now the
second board in the chain), then the absolute Board Name on
the new board changes from “.C to .B”. An absolute Board
Name always refers to a single port on a single board.
The “SET TEMPH [Board NamelALL] [value]” com
mand is used to set the SNMP temperature trap high limit.
The SET TEMPH command takes two optional parameters.
The ?rst is the Board Name. If the Board Name parameter
is not speci?ed on the command line the power manager
prompts for the Board Name with the “Board:” prompt. A
user may specify an absolute Board Name, a mnemonic
20
25
30
35
40
45
50
55
60
65
18
Board Name from the SHOW command page ?eld or the
keyword ALL to cause all boards in the chain to be modi?ed
by the command.
The second parameter is the temperature limit value to be
set. The value is in degrees Celsius and may be any value
from 1 to 125. If the value is not speci?ed on the command
line, the power manager prompts for the value with the
“Temperature:” prompt. If the value speci?ed is not within
the proper range, the following error message is displayed:
“Invalid Temperature Valid range 1 to 125”.
When the command completes the following message is
displayed “Limit Value Set Successfully on X unit(s)/port(s)
Command Completed Successfullyl”. The “X” in the mes
sage indicates the number of boards modi?ed by the com
mand.
The “SET TEMPL [Board NamelALL] [value]” command
is used to set the SNMP temperature trap low limit. The SET
TEMPL command takes two optional parameters. The ?rst
is the Board Name. If the Board Name parameter is not
speci?ed on the command line the power manager prompts
for the Board Name with the “Board:” prompt. A user may
specify an absolute Board Name, a mnemonic Board Name
from the SHOW command page ?eld or the keyword ALL
to cause all boards in the chain to be modi?ed by the
command.
The second parameter is the temperature limit value to be
set. The value is in degrees Celsius and may be any value
from 1 to 125. If the value is not speci?ed on the command
line, the power manager prompts for the value with the
“Temperature:” prompt. If the value speci?ed is not within
the proper range, the following error message is displayed:
“Invalid Temperature Valid range 1 to 125”.
When the command completes the following message is
displayed “Limit Value Set Successfully on X unit(s)/port(s)
Command Completed Successfullyl”. The “X” in the mes
sage indicates the number of boards modi?ed by the com
mand.
The “SET LOADH [Port NamelGrouplALL] [value]”
command is used to set the SNMP load sense trap high limit.
The SET LOADH command takes two optional parameters.
The ?rst is the Port Name. If the Port Name parameter is not
speci?ed on the command line the power manager prompts
for the Port Name with the “Port Name:” prompt.
The second parameter is the amps limit value to be set.
The amps value may be any value from 1 to 60. If the value
speci?ed is not within the proper range, the following error
message is displayed: “Invalid Amps Value Valid range 1 to
60”.
When the command completes the following message is
displayed “Limit Value Set Successfully on X unit(s)/port(s)
Command Completed Successfullyl”. The “X” in the mes
sage indicates the number of power manager ports modi?ed
by the command.
The “SET LOADL [Port NamelGrouplALL] [value]”
command is used to set the SNMP load sense trap low limit.
The SET LOADL command takes two optional parameters.
The ?rst is the Port Name. If the Port Name parameter is not
speci?ed on the command line the power manager prompts
for the Port Name with the “Port Name:” prompt.
The second parameter is the amps limit value to be set.
The amps value may be any value from 1 to 60. If the value
speci?ed is not within the proper range, the following error
message is displayed: “Invalid Amps Value Valid range 1 to
60”.
When the command completes the following message is
displayed “Limit Value Set Successfully on X unit(s)/port(s)