Owners manual

PG-1

Westin Automotive Products, Inc.

320 W. Covina Blvd

San Dimas, Ca. 91773

Thank You for choosing Westin products

For Additional installation assistance please call

Customer service (800) 793-7846

www.westinautomotive.com

75-1119 Rev A ECO: W15-0006 DATE: 4/29/2015

PRO TRAXX 6 OVAL STEP BARS

APPLICATION: 2015+ FORD F150 SUPER CAB

PART NUMBERS: 21-63930 21-63935

INSTALLATION INSTRUCTIONS

Complete Installation

Qty Description Qty Description

1 Driver/left Sidebar 8 8-1.25mm x 25mm Hex Bolts

1 Passenger/right Sidebar 20 8mm x 24mm OD x 2mm Washers

4 Sidebar Brackets (use for left or right) 8 8mm Lock Washers

12 8mm Plastic Washers 12 8-1.25mm Nylon Lock Nuts

(12) 8mm Plastic Washers

(4) Left or Right

Mounting Brackets

Front

Driver/left Sidebar illustrated for example only.

Arrows indicate location of threaded inserts

Front step pad is farther

away from end of tube

PROCEDURE:

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.

1. Start the installation under the driver side of the vehicle. Locate the front and rear factory running

board mounting locations along the inner side of the body, (Figure 1).

2. Slide (1) Plastic Washer over each factory mounting stud in the body panel, (Figures 2 & 3). IM-

PORTANT: The Plastic Washers are designed to prevent corrosion between the aluminum body

panel and the steel mounting brackets. Do not install the Brackets without the Plastic Washers.

3. Select (1) Mounting Bracket. NOTE: All (4) Brackets are universal and will fit left or right side. Attach

the Mounting Bracket to the (3) factory studs with (3) 8mm Flat Washers and (3) 8mm Nylon Lock

Nuts, (Figure 4). Snug but do not fully tighten the hardware.

4. Repeat Steps 1—3 to install the rear driver side Bracket.

PAGE 1
INSTALLATION INSTRUCTIONS PRO TRAXX 6 OVAL STEP BARS APPLICATION: 2015+ FORD F150 SUPER CAB PART NUMBERS: 21-63930 21-63935 Qty Description Qty 1 Driver/left Sidebar 8 1 Passenger/right Sidebar 20 4 12 Sidebar Brackets (use for left or right) 8mm Plastic Washers 8 12 Description 8-1.25mm x 25mm Hex Bolts 8mm x 24mm OD x 2mm Washers Complete Installation 8mm Lock Washers 8-1.
PAGE 2
5. Select the driver/left Sidebar. Carefully position the Sidebar onto the (3) Mounting Brackets. IMPORTANT: Do not slide, (front to back or rotate), the Sidebar on the Brackets or damage to the finish on the Sidebar may result. Attach the Sidebar to the Mounting Brackets with (4) 8mm x 25mm Hex Bolts, (4) 8mm Lock Washers and (4) 8mm Flat Washers, (Figure 5). Do not tighten hardware. 6. Level and adjust the Sidebar and tighten all hardware. 7. Repeat Steps 1—6 to install the passenger/right Sidebar. 8.
PAGE 3
(3) 8mm Plastic Washers (3) 8mm Flat Washers (3) 8mm Nylon Lock Nuts (Fig 4) Typical Bracket installation illustrated Fig 5 Attach Sidebar to each Bracket with: (2) 8mm x 25mm Hex Bolts (2) 8mm Lock Washers (2) 8mm Flat Washers Westin Automotive Products, Inc. 320 W. Covina Blvd San Dimas, Ca. 91773 75-1119 Rev A ECO: W15-0006 Thank You for choosing Westin products For Additional installation assistance please call Customer service (800) 793-7846 www.westinautomotive.