User Guide

ManualsBrandsWestin ManualsAutomotiveWestin 27-0015 Molded Step Board with Light

1,2 2 STEP BOARD, PASSENGER (1) AND DRIVER (2) (SOLD SEPARATELY)

3 8 MOUNT BRACKET

4 16 M8-1.25 X 20MM HEX HEAD BOLT

5 12 M8-1.25 HEX NUT

6 16 5/16-18 X .75 SQUARE HEAD BOLT

7 40 5/16” FLAT WASHER

8 16 5/16” LOCK WASHER

9 16 5/16” LOCK NUT

QTY

CONTENTS - CONTENIDO - CONTENU

TOOLS- HERRAMIENTA-OUTILS

13MM SOCKET

13MM WRENCH

1/2” SOCKET

RATCHET

TORQUE WRENCH

ITEM

AUTOMOTIVE PRODUCTS, INC.

INSTRUCTIONS-INSTRUCCIONES-CONSIGNES

1,2 2 ESTRIBOS, ACOMPAÑANTE (1) CONDUCTOR (2) (SE COMPRA

SEPARADO)

3 8 SOPORTE

4 16 PERNOS CON CABEZA HEXAGONAL M8-1,25 X 20MM

5 12 TUERCAS HEXAGONALES DE M8-1,25

6 16 PERNOS CON CUADRADA DE 5/16-18 X .75

7 40 ARANDELAS PLANAS DE 5/16”

8 16 ARANDELAS DE PRESIÓN DE 5/16”

9 16 TUERCA A PRESIÓN 5/16”

1,2 2 MARCHEPIEDS, PASSAGER (1) ET CONDUCTEUR (2) ACHETÉS

SÉPARÉMENT

3 8 SUPPORT

4 16 BOULONS À TÊTE HEXAGONALE M8-1,25 X 20 MM

5 12 ÉCROUS HEXAGONAUX M8-1,25

6 16 BOULONS À TÊTE CARRÉE 5/16-18 X 0,75 PO

7 40 RONDELLE PLATE 5/16 PO

8 16 RONDELLES A FREIN 5/16 PO

9 16 ÉCROU FREINÉ 5/16 PO.

DADO DE 13MM

LLAVE DE TUERCAS DE 13MM

DADO DE 1/2”

MANERAL

LLAVE DE TORQUE

DOUILLE 13MM

CLÉ 13MM

DOUILLE 1/2 PO

CLIQUET

CLÉ DYNAMOMÉTRIQUE

APPLICATION: 2002-08 CHEVY AVALANCHE

2005-08 CHEVY SUBURBAN/TAHOE/GMC YUKON, YUKON XL

APPLICATION: CHEVY AVALANCHE 2002-08

CHEVY SUBURBAN/TAHOE/GMC TYUKON, YUKON XL 2005-08

APLICACIÓN: CHEVY AVALANCHE, MOD. 2002-08

CHEVY SUBURBAN/TAHOE/GMC YUKON, YUKON XL, MOD. 2005-08

MOUNT KIT

EQUIPO DE MONTAJE

JEU DE MONTAGE

27-1645

MOLDED

STEP

BOARDS

27-0010

27-0015

27-0020

27-0025

STEP BOARDS FOR AVALANCHE WITH CLADDING

27-0010, 27-6130, 27-6135, 27-6530

STEP BOARDS AVALANCHE WITHOUT CLADDING

27-0020, 27-0025, 27-6140, 27-6145, 27-6540

75-0607 REVISION F 6/30/08

WO:

SURE-GRIP

OPTIONAL LIGHT

KIT

27-6000

SURE-GRIP

BOARDS

27-6130

27-6135

27-6530

27-6140

27-6145

27-6540

STEP 1. Remove contents from box and check for damage. Verify all parts are present. Read instructions completely before beginning. It

is strongly recommended to install the Sure Grip Gap Strip for these vehicle applications.

STEP 2. Attach mounting brackets as shown. SEE FIGURE 1.

STEP 3. Insert square head bolts as shown ( 4 per slot, 8 per board). SEE FIGURES 3 AND 4.

NOTE: For lighted boards, run wiring harness prior to attaching board to brackets (refer to Step 6). SEE FIGURES 3 AND 4. Run longer

wire harness on passenger side.

STEP 4. For Sure-Grip Running Boards, slide closure strip as shown. Set lights (if purchased) in appropriate location. Attach to Sure-Grip

Running Board as shown. SEE FIGURE 2. Drill hole through plastic strip and run wires as shown. SEE FIGURE 5.

STEP 5. Attach board to brackets as shown. Make sure board and brackets are properly aligned and tighten fasteners. Recommended

torque values are 10 FT.LBS. for 5/16” square head fasteners and 23 FT.LBS. for 8mm fasteners. SEE FIGURE 6.

NOTE: For lighted version of Molded Step Board, remove plastic cover from each end of under side of board. Proceed to Steps 6-7.

WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN RECOMMENDS USING A PROFESSIONAL

FOR THIS INSTALLATION. NOTE: AVOID AREAS OF EXCESSIVE HEAT, VIBRATION, PINCH OR ROTATION WHEN SECURING HARNESS TO

VEHICLE. CAUTION: ALWAYS USE A FUSED(+) POSITIVE SUPPLY SOURCE. UNDERCOAT SEAL FOR HARSH WEATHER.

HINT: Molded Step Boards: For longevity, check rubber seals before installation. Rubber grommets around red and blue wires going

into rear sockets, should be inserted and recessed about 1/4”. NOTE: Remove bulbs and apply white grease into sockets and

replace bulbs. Apply RTV Silicone where lights go into socket. Install lights and run wire loom as shown. SEE FIGURE 4. For Sure-Grip

Summary of content (4 pages)

PAGE 1
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES APPLICATION: 2002-08 CHEVY AVALANCHE 2005-08 CHEVY SUBURBAN/TAHOE/GMC YUKON, YUKON XL APLICACIÓN: CHEVY AVALANCHE, MOD. 2002-08 CHEVY SUBURBAN/TAHOE/GMC YUKON, YUKON XL, MOD. 2005-08 AUTOMOTIVE PRODUCTS, INC.
PAGE 2
Running Boards, run wire loom down center as shown. SEE FIGURE 3. STEP 6. Determine whether your vehicle has a positive or negative switching courtesy system or an auxiliary light source (most Fords). Obtain an accurate wiring diagram for your vehicle's courtesy light system. For positive and negative switching: Locate a pass-through point (usually under carpet at driver side door sill) for the wire harness. Locate main courtesy wire (usually wire lead to dome light).
PAGE 3
PASO 7. **Asegúrese de no pasar ningún cable cerca de piezas móviles (por ejemplo, el eje del motor) o cerca de ninguna fuente de generación de calor (por ej., transmisión, motor, escape). Fuente de luz auxiliar: Identifique la conexión de la fuente de luz auxiliar debajo del vehículo, que generalmente está instalada en la parte posterior del salpicadero delantero o trasero (consulte el manual del propietario). VEA LA FIGURA 7. COMPRUEBE LA FUENTE ANTES DE REALIZAR LA CONEXIÓN.
PAGE 4
EXISTING INSERT IN BODY PANEL PERFORACIÓN EXISTENTE EN EL PANEL DE LA CARROCERÍA PERFORATION EXISTANTE DANS LE PANNEAU DE CAROSSERIE 5 8 7 7 8 4 3 NOTE: FRONT AND REAR BRACKETS ONLY ON 05’ AND NEWER VEHICALS NOTA: SOPORTES DELANTEROS Y TRASEROS EN VEHÍCULOS MODELO 2005 Y MÁS NUEVOS REMARQUE : LES SUPPORTS AVANT ET ARRIÈRE SEULEMENT POUR LES VÉHICULES 2005 ET PLUS RÉCENTS NOTE: USED ONLY ON 04’ AND OLDER VEHICALS NOTA: SE USA SÓLO EN VEHÍCULOS MOD.