Instructions / Assembly

ManualsBrandsWestinghouse ManualsLED Bulbs150-Watt Equivalent Daylight T23 Corn Cob Medium Base LED Light Bulb

1. CAUTIONS:

• Turn power oﬀ before inspection, installation, or removal.

• Risk of electric shock - Do not use where exposed to water or weather.

• Suitable for Damp Locations - The lamp is suitable for use in wet locations when used in an outdoor rated xture.

• Do not open – no user serviceable parts inside.

• LED Retrot lamps require 120V-277V input voltage.

• Not for use with dimmers.

• This device is not intended for use with emergency exit xtures or emergency exit lights.

• This device complies with Part 15 of the FCC rules and has been tested and found to comply with the limits for a Class B digital device. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. Any changes or modications not expressly approved by the manufacturer could void the user's authority to operate

the equipment.

2. INSTRUCTION:

STEP 1: Disconnect power from the luminaire and follow proper lockout/tagout procedures before beginning installation or maintenance.

STEP 2: Remove the existing lamp. Dispose of the lamps per local equirements.

STEP 3: Disconnect and remove the existing ballast, capacitor, and ignitor. Dispose of the components per local requirements.

STEP 4: Connect the Line wire (Line/Hot) to the center contact (eyelet) of the lamp holder.

STEP 5: Connect the Neutral wire (Common) to the shell of the lamp holder.

STEP 6: Insert and screw in the LED Retrot lamp into the lamp holder.

STEP 7: Close the wiring compartment. Watch to be sure the wires are not pinched, bound, or crimped when closing the compartment.

STEP 8: Switch on the power.

3. WIRING DIAGRAMS:

INSTALLATION AND SAFETY INSTRUCTIONS

ESF-WH-0211

Replacing Self Ballasted CFL Lamp

Self ballasted

CFL Lamp

LED Retrofit

Lamp

HPS / HID

lamp

Ballast

Ignitor

Capacitor

Replacing

with

Replacing

with

Ballast

Ignitor

Capacitor

Replacing HPS/HID Lamp

Self Ballasted CFL Wiring Diagram

LED Retrofit Lamp Wiring Diagram

HPS/HID Wiring Diagram

, Westinghouse, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.

Summary of content (3 pages)

PAGE 1
INSTALLATION AND SAFETY INSTRUCTIONS 1. CAUTIONS: • Turn power oﬀ before inspection, installation, or removal. • Risk of electric shock - Do not use where exposed to water or weather. • Suitable for Damp Locations - The lamp is suitable for use in wet locations when used in an outdoor rated fixture. • Do not open – no user serviceable parts inside. • LED Retrofit lamps require 120V-277V input voltage. • Not for use with dimmers.
PAGE 2
INSTRUCCIONES DE INSTALACIÓN Y SEGURIDAD 1. ADVERTENCIAS: • Desconecte el suministro eléctrico antes de inspeccionar, instalar o extraer. • Riesgo de descarga eléctrica - No utilizar en lugares expuestos al agua o a las condiciones climáticas. • Apto para lugares húmedos - La lámpara es apta para el uso en lugares húmedos o en un artefacto clasificado para exteriores. • No abrir - No contiene piezas reparables por el usuario.
PAGE 3
INSTALLATION ET CONSIGNES DE SÉCURITÉ 1. MISES EN GARDE: • Éteindre le courant avant inspection, installation ou retrait. • Risque de choc électrique - Ne pas utiliser en cas d'exposition à l'eau ou aux intempéries. • Adaptée aux endroits humides - La lampe peut être utilisée dans les endroits humides si elle est monté sur un dispositif adapté à l'extérieur. • Ne pas ouvrir - Il n'y a aucune pièce nécessitant l'intervention de l'utilisateur à l'intérieur.