Owner’s Manual Outdoor Lighting Fixture Installation Instructions W-070 030904 Please write model number here for future reference: / Veuillez noter le numéro de modèle aux fins de référence ultérieure: / Por favor, incluya el número del modelo aquí para futura referencia:
ASSEMBLY INSTRUCTIONS FOR OUTDOOR LIGHT FIXTURE Congratulations on your Westinghouse purchase. This fixture has been designed to give you many years of beauty and service. Please email questions and comments to: catalogroom@westinghouselighting.com. NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any packing materials (see figure 1).
FIGURE 1. GREEN GROUNDING SCREW (F) *OUTLET BOX (C) *OUTLET BOX SCREWS (D) SIDE HOLE (G) GROUND WIRE BACK PLATE (H) FIXTURE COVER (O) MOUNTING SCREWS (A) UNIVERSAL MOUNTING PLATE (B) WIRE CONNECTORS (E) CAP NUTS (I) NIPPLE (P) GLASS SHADE (J) FLAT WASHER (N) HEX NUT (M) COVER (L) FINIAL (K) Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture.
MOUNTING AND WIRING INSTRUCTIONS CAUTION: For fixtures labeled for outdoor and wet location use, provide a water-tight seal between the fixture and the mounting surface by using silicone or similar caulking. NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures meet all UL specifications. 1. Turn off power at circuit box to avoid possible electric shock. 2. Thread mounting screws (A) into universal mounting plate (B) (see fig. 1). 3.
LES INSTRUCTIONS D'ASSEMBLAGE DE L'APPAREIL D'ÉCLAIRAGE POUR UTILISATION EXTÉRIEURE Félicitations ! Vous avez acheté un produit de Westinghouse Lighting. Cet appareil d'éclairage a été conçu pour durer de nombreuses années. Veuillez envoyer vos questions et commentaires par courriel, à l'adresse suivante : catalogroom@westinghouselighting.com NOTA : Déballez soigneusement l'appareil d'éclairage et les pièces. Assurez-vous que toutes les pièces y sont avant de mettre l’emballage au rebut (voir fig. 1).
FIGURE 1.
INSTRUCTIONS DE MONTAGE ET DE RACCORDEMENT NOTA : Underwriters Laboratories (UL) n’exige pas que tous les appareils d’éclairage comportent des fils de mise à la terre. Ces appareils satisfont cependant à toutes les spécifications UL. 1. Mettez l’interrupteur de la boîte de fusibles à « OFF » afin d’éviter le risque d’électrocution. 2. Vissez les vis de fixation (A) dans la plaque universelle de fixation (B) (voir fig. 1). 3.
INSTRUCCIONES DE MONTAJE PARA EL ARTEFACTO DE ILUMINACIÓN PARA EXTERIORES Le felicitamos por comprar este producto de Westinghouse Lighting. Este producto ha sido diseñado para brindarle muchos años de belleza y servicio. Si tiene preguntas o comentarios, por favor envíe un mensaje electrónico a: catalogroom@westinghouselighting.com NOTA: Extraiga cuidadosamente el artefacto y las piezas. Verifique que contenga todas las partes requeridas (consulte la figura 1) antes de descartar los materiales de empaque.
FIGURA 1. PLACA POSTERIOR (H) CUBIERTA DEL ARTEFACTO (O) TORNILLO VERDE DE TIERRA (F) *CAJA DE EMBUTIR (C) *TORNILLOS CAJA DE EMBUTIR (D) ORIFICIO LATERAL (G) CABLE DE TIERRA TORNILLOS DE MONTAJE (A) PLACA DE MONTAJE UNIVERSAL (B) TUERCAS TAPA (I) NIPLE (P) CONECTORES DE ROSCA (E) PANTALLA DE VIDRIO (J) ARANDELA PLANA (N) TUERCA HEXAGONAL (M) CUBIERTA (L) FLORON (K) Los dibujos pueden no coincidir exactamente con el artefacto incluido.
INSTRUCCIONES DE MONTAJE Y CABLEADO NOTA: Underwriters Laboratories (U.L.) no requiere que todos los artefactos tengan cables de tierra. Estos artefactos cumplen con todas las especificaciones U.L. 1. Desconecte el suministro eléctrico en la caja de fusibles para evitar la posibilidad de descarga eléctrica. 2. Enrosque los tornillos de montaje (A) en la placa de montaje universal (B) (vea la fig. 1). 3.
FIGURE 2. GROUP A: CONNECT TO BLACK HOUSE WIRE GROUP B: CONNECT TO WHITE HOUSE WIRE BLACK WHITE WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER BROWN, GOLD OR BLACK WITHOUT TRACER BROWN, GOLD OR BLACK WITH TRACER NOTE: When parallel wire (SPT I & SPT II) is used; the neutral wire is square shaped and ridged, and the hot wire will be round in shape and smooth. (See below.) WARNING Turn off electricity to the mounting site before beginning installation.
CLEANING AND CARE To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can discolor the finish of fixture. Extend-A-Finish Laquer Conditioner, Item#70295, is recommended once a year to clean, condition, and protect fixture. Do not use scouring pads, powders, steel wool or abrasive paper to clean this fixture.