Installation Sheet
LED 6” RETROFIT TRIM INSTALLATION INSTRUCTIONS
Please read carefully and save these instructions, as you may need them
at a later date.
GENERAL: All electrical connections must be in accordance with local and
National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper
electrical wiring connections obtain the services of a qualified electrician.
Remove the trim from the box and make sure that no parts are missing by
referencing the PARTS illustration.
THIS RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF A LED
LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE
DETERMINED BY CSA OR CANADIAN AUTHORITIES HAVING JURISDIC-
TION.
WARNING: RISK OF ELECTRIC SHOCK. INSTALL THIS
TRIM IN RECESSED HOUSINGS THAT HAVE DIMENSIONS
SHOWN IN FIG. 1.
WARNING - Risk of fire or electric shock. LED Retrofit Kit installation requires
knowledge of luminaire electrical systems. If not qualified, do not attempt
installation. Contact a qualified electrician.
WARNING - Risk of fire or electric shock. Install this kit only in the luminaires
that have the construction features and dimensions shown in the photographs
and/or drawings.
Do not make or alter any open holes in an enclosure of wiring or electrical
components during kit installation.
WARNING - To prevent wiring damage or abrasion, do not expose wiring to
edges of sheet metal or other sharp objects.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICA-
BLE CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
ASSEMBLY AND INSTALLATION
INCANDESCENT HOUSINGS
1. Turn off power at circuit box to avoid possible electric shock.
2. Thread the SOCKET ADAPTER into the SOCKET. (FIG. 2)
3. Plug the CONNECTOR of the RETROFIT TRIM onto the CONNECTOR of the
SOCKET ADAPTER ASSEMBLY. (FIG. 3)
4. Squeeze both TORSION SPRING arms together and insert into the TORSION
SPRING SLOTS (or RECEIVER BRACKETS) of the CAN. Tuck all wires into
the CAN and carefully push the RETROFIT TRIM into CAN. (NOTE: To provide
enough room in shallow cans, carefully position SOCKET ADAPTER and
SOCKET adjacent to the long side of the LED DRIVER prior to inserting the
RETROFIT TRIM into the CAN.) (FIG. 4)
DIMMING
Although this product is compatible with most common residential type
dimmers, dimming performance depends on dimmer, dimmer setting (for
dimmers with brightness range adjustments), wiring method, and the number of
LED modules. For best results, set dimmer position at maximum before
adjusting to a lower light level.
Recommended Dimmers (minimum load for four LED modules maybe required
for optimal dimming performance): LEVITON: 6683, 6631-LA, 603-6631-A,
6631-A, NO.IPL06, IPI10-1LZ, 6683-10Z, IPI06-1LZ and LUTRON:
S-603PH-WH
LIMITED WARRANTY
This lamp is warranted to be free from defects in materials and workmanship for 5
years. If the product fails during the warranty period, return defective product to
seller. Warranty terms and conditions of seller apply. If replacement product is
not available through seller, please contact www.westinghouselighting.com/con-
tact-us.
WARNING - RISK OF ELECTRIC SHOCK. DISCONNECT MAIN
POWER AT FUSE OR CIRCUIT BREAKER BEFORE INSTALLING
OR SERVICING THE FIXTURE.
5 in. – 7 in.
6 in.
FIG. 1
FIG. 2
FIG. 3
PARTS
SOCKET ADAPTER
ASSEMBLY
RETROFIT TRIM
HOUSING DIMENSIONS
FIG. 4
ES-WH-037
and Westinghouse are trademarks of
Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting
All Rights Reserved.
Made in China
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
www.westinghouselighting.com