Installation Sheet

LED 6” RETROFIT TRIM INSTALLATION INSTRUCTIONS
Please read carefully and save these instructions, as you may need
them at a later date.
GENERAL: All electrical connections must be in accordance with local and National
Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring
connections obtain the services of a qualified electrician.
Remove the trim from the box and make sure that no parts are missing by
referencing the PARTS illustration. The rubber behind the trim will make the down
light completely flush with ceiling all the way around for better installation.
THIS RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF A LED
LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE
DETERMINED BY CSA OR CANADIAN AUTHORITIES HAVING JURISDICTION.
WARNING: RISK OF ELECTRIC SHOCK. INSTALL THIS
TRIM IN RECESSED HOUSINGS THAT HAVE DIMENSIONS
SHOWN IN FIG. 1.
WARNING - Risk of fire or electric shock. LED Retrofit Kit installation requires
knowledge of luminaire electrical systems. If not qualified, do not attempt installa-
tion. Contact a qualified electrician.
WARNING - Risk of fire or electric shock. Install this kit only in the luminaires that
have the construction features and dimensions shown in the photographs and/or
drawings.
Do not make or alter any open holes in an enclosure of wiring or electrical
components during kit installation.
WARNING - To prevent wiring damage or abrasion, do not expose wiring to edges
of sheet metal or other sharp objects.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION
OF THE PRODUCT AND THE HAZARDS INVOLVED.
ASSEMBLY AND INSTALLATION
INCANDESCENT HOUSINGS
1. Turn off power at circuit box to avoid possible electric shock.
2. Thread the SOCKET ADAPTER into the SOCKET. (FIG. 2)
3. Plug the CONNECTOR of the RETROFIT TRIM onto the CONNECTOR of the
SOCKET ADAPTER ASSEMBLY. (FIG. 3)
4. Squeeze both TORSION SPRING arms together and insert into the TORSION
SPRING SLOTS (or RECEIVER BRACKETS) of the CAN. Tuck all wires into
the CAN and carefully push the RETROFIT TRIM into CAN. (NOTE: To provide
enough room in shallow cans, carefully position SOCKET ADAPTER and
SOCKET adjacent to the long side of the LED DRIVER prior to inserting the
RETROFIT TRIM into the CAN.) (FIG. 4)
DIMMING
Although this product is compatible with most common residential type dimmers, dimming
performance depends on dimmer, dimmer setting (for dimmers with brightness range
adjustments), wiring method, and the number of LED modules. For best results, set dimmer
position at maximum before adjusting to a lower light level.
Recommended Dimmers (minimum load for four LED modules maybe required for optimal
dimming performance): LEVITON: 6683, 6631-LA, 603-6631-A, 6631-A, NO.IPL06, IPI10-1LZ,
6683-10Z, IPI06-1LZ and LUTRON: S-603PH-WH
FIVE-YEAR LIMITED WARRANTY
Westinghouse Lighting warrants that this lamp will be free from defects in material
and workmanship and will work for 5 years (based on up to 3 hours average usage
per day for 7 days per week). If the product fails during the warranty period, return
defective product to retailer. Warranty terms and conditions of retailer apply. If
replacement product is not available at retail store, please contact consumersup-
[e-mail] or return the product in the original package with
receipt to manufacturer at: 12401 McNulty Road, Philadelphia, PA 19154-1029.
This limited warranty does not cover lamps subject to accident, neglect, abuse,
misuse or acts of God. REPLACEMENT IS YOUR SOLE REMEDY. EXCEPT TO
THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRAN-
TIES ARE LIMITED TO THE DURATION OF THIS WARRANTY PERIOD.
LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS EXPRESSLY
EXCLUDED. Some states do not allow exclusion of incidental or consequential
damages, so the above exclusion may not apply. This warranty gives you specific
legal rights, but you may also have other rights that vary from state to state.
WARNING - RISK OF ELECTRIC SHOCK. DISCONNECT MAIN
POWER AT FUSE OR CIRCUIT BREAKER BEFORE INSTALLING
OR SERVICING THE FIXTURE.
5 in. – 7 in.
6 in.
FIG. 1
FIG. 2
FIG. 3
PARTS
SOCKET ADAPTER
ASSEMBLY
RETROFIT TRIM
HOUSING DIMENSIONS
FIG. 4
ESF-WH-037
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
www.westinghouselighting.com
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF
are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting
All rights reserved.
Made in China