Installation Manual
W-687
032820
Owner’s Manual
LED Indoor Lighting Fixture
Installation Instructions
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
WARRANTY INFORMATION
This luminaire is warranted to be free from defects in materials and workmanship for 5 years. If the
product fails during the warranty period, return defective product to seller. Warranty terms and
conditions of seller apply. If replacement product is not available through seller, please contact
www.westinghouselighting.com/contact-us.
WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
1. Read all instructions carefully before installation and operation.
2. If you are not familiar with federal, state, and local electrical codes, it is recommended that you
consult with a qualied electrician.
3.
Suitable for used in damp locations.
4. Non-replaceable LEDs.
5. Caution: LEDs emit bright light. Avoid looking directly into the light source for prolonged periods to
avoid eye damage.
6. Not to be used with electronically controlled switches.
Congratulations on your Westinghouse purchase. This xture has been designed to give you many
years of beauty and service. For questions and comments, please visit www.westinghouselight-
ing.com/contact-us.
NOTE: Carefully unpack xture and parts. Make sure all parts are included before discarding any
packing materials.
CLEANING AND CARE
To clean, wipe xture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can
discolor the nish of xture. Do not use scouring pads, powders, steel wool or abrasive paper to clean
this xture.
INSTALLATION STEPS
NOTE: Instructions apply to both round and square slim
recessed LED downlights.
1. Drill hole in ceiling and prepare supply wires. Install
and strip away the outer jacket of the supply wire 6’’
(15 cm) and strip the individual wires 5/8’’ (1.6 cm).
(Fig. 1)
Fig. 1
MIN. 4.25’’( 10.8 cm)
4.38’’ ( 11.1 cm)
MAX. 4.5’’ ( 11.4 cm)
4” Recess:
MIN. 6.14’’( 15.6 cm)
6.22’’ ( 15.8 cm)
MAX. 6.30’’ ( 16 cm)
6” Recess:
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting.
All rights reserved.
Made in China
NOTE: THIS FIXTURE IS SUITABLE FOR USE WITH DIMMABLE SWITCHES, SEE BELOW FOR LIST OF
COMPATIBLE DIMMERS.
EGNAR GNIMMID # ledoM dnarB
DVCL-153PR-WH, CTCL-153PDH-WH, TGCL-153PH-WH,
MACL-153MH-WH, P-PKG1W-WWH-R
SAL06P-LA-K
R62-06674-P0W, R12-06672-1LW
Lutron
Leviton
Eaton
10-100%
Not recommended for use with motion sensors, light sensors, timers or any other external controls.
2. Open the hardwire box swing cover and remove the
appropriate knockout, insert the electrical supply cable
through the knockout. Use the wirenuts to connect the
white wire from the supply wire with the white wire of
the junction box. Match the black wire from the supply
wire with the black wire of the junction box. Match the
copper wire from the supply wire and with the green
wire of the junction box. (Fig. 2)
4. Place junction box into the ceiling through cut-out.
(Fig. 3)
3. Connect junction box to recessed LED panel with the
quick lock connector. (Fig. 3)
5. Pull the spring clips on the xture up and through the
cut-out. Spring clips should close above the ceiling
and secure recessed LED module in place. (Fig. 4)
Fig. 2
Black wire
Wire connector
Power supply
White wire
Green wire
Cable to xture
Fig. 3
Fig. 4