Installation Sheet

9. Thread the fixture screws (8) into the appropriate threaded holes of the outlet box (1) and tighten securely.
10. Final assembly - Secure the lens (3) and ring (12) to fixture pan (2) using four cap nuts (13).
11. Installation complete, restore power at the circuit breaker and turn light switch on to activate this fixture.
W-719
022821
Owner’s Manual
LED Indoor Lighting Fixture
Installation Instructions
WARRANTY INFORMATION
This Westinghouse lighting fixture is warranted against defects in material and workmanship for a period
of five years from pur chase date. This warranty is in lieu of all other warranties expressed or implied.
This warranty does not cover acts of nature such as lightening damage, or corrosion and discoloration of
components, nor does it cover damages caused through abuse, improver installation, surges in electric
current, or acts of third parties.
This warranty does not cover the costs of removing and re-installing the lighting fixture.
If this product fails for any reason covered by this warranty, please contact us at www.westinghouselight-
ing.com/contact-us.
WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
1. Read all instructions carefully before installation and operation.
2. If you are not familiar with state and local electrical codes, it is recommended that you consult with a
qualified electrician.
3. Do not use in wet locations, use indoors only.
4. Non-replaceable LEDs.
5. Caution: LEDs emit bright light. Avoid looking directly into the light source for prolonged periods to
avoid eye damage.
6. Not to be used with a dimming circuit or any other electronically controlled switch.
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
Congratulations on your Westinghouse purchase. This fixture has been designed to give you many years of
beauty and service. For questions and comments, please visit www.westinghouselighting.com/contact-us.
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any packing
materials.
INSTALLATION STEPS
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting. All rights reserved. Made in China
1. Turn off power at fuse box to avoid possible electric shock.
2. Remove lens from fixture pan and place fixture pan (2) flush against ceiling at desired outlet box (1)
location. Using outside set of fixture pan holes (16) as a guide, mark where pilot holes are to be drilled.
3. Drill 4 - 1/8 inch holes at each pencil mark then insert wall anchors (14) by gently tapping with a hammer.
Partially thread anchor screws (15) into wall anchors (14).
4. Pull the supply wires (4 & 5) and house ground wire (6) out from the outlet box (1).
5. Connect the fixture ground wire (11) to the house ground wire (6) together using wire nut (7).
6. Wrap all wire connections with electrical tape to ensure secure connection.
7. Electrical connections. Connect the black fixture wire (10) to the black supply wire (5), and the white
fixture wire (9) to the white supply wire (4) using wire nut (7). Wrap all wire connections with electrical
tape to ensure secure connection.
8. Carefully tuck all wires back into the outlet box. Place the fixture pan (2) over outlet box and feed anchor
screws (15) through the fixture pan's keyhole slots. Slide the fixture pan (2) until anchor screws (15) slide
into the narrow end of the keyhole slots and tighten firmly.
CLEANING AND CARE
To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can discolor
the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to clean this fixture.
NOTE: THIS FIXTURE IS SUITABLE FOR USE WITH DIMMABLE SWITCHES, SEE BELOW FOR LIST OF
COMPATIBLE DIMMERS.
Lutron DVCL-153P, DVCL-153PR-WH, MACL-153M, PD-6WCL, MRF2-6CL, 10-100%
TGCL-153PH-WH-C, SCL-153P, DVCL-253P, CTCL-153PH, CTCL-153P,
DVCL-253P-WH, PD-10NXD
Leviton DSL06-1LZ, C22-6672-1LW, C26-RNL06-TW, 001-DW6HD-1BZ, 10-100%
RDL06-001-10Z, TSL06, IPL06-011-10Z, 06674-002-10W
Brand Model # DIMMING RATING
1. OUTLET BOX (EXCLUDED)
2. FIXTURE PAN
3. LENS
4. WHITE SUPPLY WIRE
5. BLACK SUPPLY WIRE
6. HOUSE GROUND WIRE
7. WIRE NUTS
8. FIXTURE SCREW
9. WHITE FIXTURE WIRE
10. BLACK FIXTURE WIRE
11. FIXTURE GROUND WIRE
12. RING
13. CAP NUTS
14. WALL ANCHOR 4PCS
15. ANCHOR SCREW 4PCS
16. OUTSIDE FIXTURE PAN HOLES
Not recommended for use with motion sensors, light sensors, timers or any other external controls.
1
4
2
3
14
7
5
6
9
10
11
16
8
15
12
13