ETL-ES-GW-Alloy LED-WH16 Owner's Manual Manual del usuario Alloy LED Please write model number here for future reference: / Por favor, incluya el número del modelo aquí para futura referencia: Net Weight: Peso Neto: 14.76 LBS 6.
ETL-ES-GW-Alloy LED-WH16 Safety tips OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT TO OUTLET BOX MARKED 'ACCEPTABLE FOR FAN SUPPORT OF 35 LBS (15.9 KG) OR LESS' AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX AND/OR SUPPORT DIRECTLY FROM BUILDING STRUCTURE. MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF LUMINARIES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND MAY NEED TO BE REPLACED.
ETL-ES-GW-Alloy LED-WH16 Consejos de seguridad HAGA LO SIGUIENTE: LEA Y GUARDE ESTAS INSTRUCCIONES ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELÉCTRICA O HERIDAS GRAVES PERSONALES, MONTE EN UNA CAJA DE EMBUTIR ROTULADA “ADECUADA PARA VENTILADORES DE 35 LB (15,9 KG) O MENOS” UTILIZANDO LOS TORNILLOS DE MONTAJE INCLUIDOS CON LA CAJA DE EMBUTIR Y/O MONTE DIRECTAMENTE EN LA ESTRUCTURA DEL EDIFICIO LA MAYORÍA DE LAS CAJAS DE EMBUTIR UTILIZADAS .
ETL-ES-GW-Alloy LED-WH16 Features Características DOWNROD INSTALLATION instalación con varilla vertical SLOPED CEILING INSTALLATION INSTALACIÓN PARA TECHO INCLINADOS Note: For sloped ceiling installation, please refer to westinghouselighting.com for specially designed canopy kit options. Nota: Para instalación en techo inclinados, visite westinghouselighting.com para opciones de juegos de dosel especificamente disenados.
ETL-ES-GW-Alloy LED-WH16 Features Características COMBO-BLADE Combo-Blades feature two high quality finishes on one blade. Select the one that best complements your decor, or change the style with just a flip of the blade. NOTE: Combo-Blade finishes vary, depending upon model. ALETAS DE DOBLE CARA Las aletas del rotor de doble cara presentan dos superficies con un acabado de alta calidad.
ETL-ES-GW-Alloy LED-WH16 pREPARING for installation Preparando Para la instalación 1 2 Unpack and inspect fan carefully to be certain all contents are included. Turn off power at fuse box to avoid possible electrical shock. Use metal outlet box suitable for fan support (must support 35 lbs). Before attaching fan to outlet box, ensure the outlet box is securely fastened by at least two points to a structural ceiling member (a loose box will cause the fan to wobble).
ETL-ES-GW-Alloy LED-WH16 Mounting bracket Installation Instalación con soporte de montaje 3 2 1 1 2 Remove the screws from the two mating holes (2) on the canopy. Loosen (do not remove) the screws in the mating slots (1) on the canopy. Rotate the mounting bracket and remove from the canopy. Quite los tornillos de los dos agujeros coincidentes (2) del dosel. Afloje (no quite) los tornillos de las ranuras coincidentes (1) del dosel. Gire el soporte de montaje y sepárelo del dosel.
ETL-ES-GW-Alloy LED-WH16 DOWNROD PREPARATION Preparando la Varilla vertical Mounting bracket Installation Instalación con soporte de montaje 5 4 3 Install mounting bracket to outlet box in ceiling using the screws and washers provided with the outlet box. 1 2 Remove clamp pin (1) and cross pin (2) from downrod (3). Instale el soporte de montaje a la caja de embutir del techo con la tornillería suministrada con la caja de embutir.
ETL-ES-GW-Alloy LED-WH16 DOWNROD PREPARATION Preparando la Varilla Vertical 6 7 3 2 1 2 1 Lossen the downroad ball (1) from downrod (2) by removing the screw (3). Slide downrod ball (1) off of downrod and remove pin (2). Afloje la bola de la varilla vertical (1) de la varilla vertical (2) quitando el tornillo (3). Deslice la bola de la varilla vertical (1) hasta separarla de la varilla vertical y quite el pasador (2).
ETL-ES-GW-Alloy LED-WH16 DOWNROD INSTALLATION Instalacion de la Varilla Vertical 8 2 3 1 4 Choose a MOUNTING OPTION, either Normal Downrod Option using the included downrod, or Extended Downrod Option using a longer downrod (purchased separately). Insert motor wires through the selected downrod and insert the downrod into the downrod coupling. Make sure to align the hole in the downrod with the hole in the downrod coupling. Install cross pin (1) removed in step 5 through coupling and downrod.
ETL-ES-GW-Alloy LED-WH16 DOWNROD PREPARATION Preparando la Varilla Vertical 9 Re-install pin into downrod, and slide downrod ball up to the top of the downrod. Re-install the screw to secure ball to downrod. Note: Some extended downrods have a pre-drilled set-screw hole. If a pre-drilled hole is present in the extended downrod, tighten the set screw into the pre-drilled hole in the extended downrod.
ETL-ES-GW-Alloy LED-WH16 Blade Installation Instalación de las aletas Blade Installation Instalación de las aletas 11 10 1 2 3 Attach blade assembly to motor using the noise-dampening motor gaskets and motor screws provided. Tighten screws securely. Fije el conjunto de las aletas al motor usando las juntas reductoras de sonido del motor y los tornillos para el motor incluidos. Apriete los tornillos asegurándolos.
ETL-ES-GW-Alloy LED-WH16 MOUNTING MONTAJE 12 13 Carefully lift fan assembly onto mounting bracket. Rotate fan until notch on downrod ball (1) engages the ridge on the mounting bracket (2). This will allow for hands free wiring. With bracket holding fan assembly, make electrical connections using the following step for wiring instructions. Levante con cuidado el conjunto del ventilador hasta el soporte de montaje.
ETL-ES-GW-Alloy LED-WH16 wiring OPTIONS OPCIÓN DE CABLEADO 14 PULL CHAIN WIRING OPTION WALL CONTROL WIRING OPTION 15 Follow diagram above to make wiring connections for fan pull chain control. Follow diagram above to make wiring connections for wall control operation.
ETL-ES-GW-Alloy LED-WH16 Secure To Ceiling Asegure el ventilador al TECHO 16 For downrod fans, slide the canopy up to the mounting bracket. Para ventiladores con varilla vertical, deslice el dosel hacia arriba hasta el soporte de montaje. 3 1 2 The canopy has two mating slots (1) and two mating holes (2). Position both slots on canopy directly under and in line with two screws in the mounting bracket (3). Lift the canopy, allowing the two screws to slide into the mating slots.
ETL-ES-GW-Alloy LED-WH16 Light fixture installation Instalación del artefacto luminoso 17 18 1 2 Install light bulbs (included). Instale las bombillas de luz (incluidas). Locate the indentations on the neck of the glass (2) and align with the protrusions from the light kit (1). Lift the glass up allowing the protrusions to engage the indentations on the glass, and twist the glass clockwise to lock into place.
ETL-ES-GW-Alloy LED-WH16 19 Assemble decorative fob and extension chains from hardware bag to fan pull chains by inserting end of chain into chain coupling. Confirm chains are held by lightly pulling both chains in coupling. Conecte las cadenilla largas de tiro con las piezas finales correspondientes, a las cadenilla del ventilador, introduciendo el extremo de la cadenilla larga en la pieza de unión.
ETL-ES-GW-Alloy LED-WH16 OPERATION AND MAINTENANCE Operation Turn on the power and check operation of fan. The pull chain controls the fan speeds as follows: 1 pull - high; 2 pulls - medium; 3 pulls - low; 4 pulls - off. Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans and so on. The slide switch controls direction, forward or reverse. Warm weather/down position - (Forward) Fan turns counterclockwise direction.
ETL-ES-GW-Alloy LED-WH16 Operación y mantenimiento Operación Encienda el ventilador y verifique su funcionamiento. La cadenilla de tiro controla las velocidades del ventilador de la siguiente manera: 1 jalón – rápida; 2 jalones - mediana; 3 jalones - lenta; 4 jalones - apagado. Las velocidades para clima cálido o frío dependen de factores como el tamaño de la habitación, la altura del ventilador, el número de ventiladores, etc.
ETL-ES-GW-Alloy LED-WH16 Troubleshooting guide If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this troubleshooting chart. If a problem cannot be remedied, please consult with your qualified electrician and do not attempt any electrical repairs yourself. TROUBLE SUGGESTED REMEDY 1. If fan does not start: 1.
ETL-ES-GW-Alloy LED-WH16 Guía para solucionar problemas Si tiene dificultades para hacer funcionar su nuevo ventilador, podría ser a causa del armado, instalación o cableado incorrectos. En algunos casos, estos errores de instalación podrían ser confundidos con defectos. Si experiencia alguna falla, consulte esta guía para solucionar problemas. Si no puede solucionar el problema, consulte a un electricista calificado y no intente reparar conexiones eléctricas. PROBLEMA SOLUCIÓN SUGERIDA 1.
ETL-ES-GW-Alloy LED-WH16 22
ETL-ES-GW-Alloy LED-WH16 PARTS LIST LISTA DE REPUESTOS 1 # Description 1 . . . . . . . . . . . . . . . . . . Mounting Bracket (assembled with Canopy) 2 . . . . . . . . . . . . . . . . . . Blade Bracket (qty. 3) 3 . . . . . . . . . . . . . . . . . . Blade (qty. 3) 4 . . . . . . . . . . . . . . . . . . Glass shade 5 . . . . . . . . . . . . . . . . . . Capacitor 6 . . . . . . . . . . . . . . . . . . Hardware Pack 7 . . . . . . . . . . . . . . . . . .
ETL-ES-GW-Alloy LED-WH16 Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com , WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation Used under license by Westinghouse Lighting All rights reserved.
