UL-ES-SilverdaleES-INSTALOC WH09 PREPARING FOR INSTALLATION ANTES DE LA INSTALACIÓN 1 2 Unpack and inspect fan carefully to be certain all contents are included. Turn off power at fuse box to avoid possible electrical shock. Use metal outlet box suitable for fan support (must support 35 lbs). Before attaching fan to outlet box, ensure the outlet box is securely fastened by at least two points to a structural ceiling member (a loose box will cause the fan to wobble).
UL-ES-SilverdaleES-INSTALOC WH09 3 4 1 3 2 3 On the mounting plate: Loosen the screw in the hole with the red mark (1) , and the screw on the opposite side (2). (Do not remove). Remove the two screws and star washers from the holes on either side of the hole with the red mark (3). Make wire connections to mounting plate. See wiring diagram in next step. NOTE: For safety, please refer to steps #3 and #15 of Safety Tips on page 2.
UL-ES-SilverdaleES-INSTALOC WH09 This fan should be used with a switch marked "Fan Speed Control Switch", or "General Use Switch". Este ventilador se debe usar con un interruptor marcado "Fan Speed Control Switch" (interruptor de control de velocidad para ventilador), o "General Use Switch" (interruptor de uso general).
UL-ES-SilverdaleES-INSTALOC WH09 7 9 8 Choose a MOUNTING OPTION Elija una OPCIÓN DE MONTAJE NORMAL DOWNROD OPTION If installing downrod supplied with fan, proceed to step 10. Make sure that all exposed wiring is secured inside wire nuts. NOTE: Wires from house may vary in color and may not include ground wire. When wiring is complete, gently push connections into junction box with wire nuts pointing up. Refer to Point 3 of Safety Tips on Page 2.
UL-ES-SilverdaleES-INSTALOC WH09 10 1 Note: Make sure your ladder is placed so you see the red mark (1) on the mounting plate edge. Make sure red arrow sticker (2) on the canopy is lined up with red mark on the mounting plate. 3 2 Hold fan unit (with both hands) so that both the red mark on the mounting plate, and red arrow on the canopy are facing you. Lift fan up aligning arrow and red mark and push canopy assembly up to the mounting plate to plug in.
UL-ES-SilverdaleES-INSTALOC WH09 12 11 1 2 1 2 Twist canopy clockwise as shown to engage screws into "L-shaped" holes (1). Line up and install the screws and star washers into the closed holes (2). Tighten all screws to secure the canopy to the mounting plate. Gire el dosel en sentido horario como se indica para enganchar los tornillos en los agujeros con forma de “L” (1). Alinee los tornillos y las arandelas en estrella colocándolos dentro de los agujeros tapados (2).
UL-ES-SilverdaleES-INSTALOC WH09 13 14 1 2 Attach the fan blades to the blade brackets by fitting the three keyslots (1) on the blade onto the turnkey mechanisms (2) on the blade bracket. Rotate the turnkey mechanisms 90˚ to secure the blade to the bracket. Fije las paletas del ventilador a los soportes para paletas alineando las tres ranuras (1) de la paleta con los mecanismos de traba con llave (2) en el soporte para paletas.
UL-ES-SilverdaleES-INSTALOC WH09 15 17 16 1 Rotate locking ring (1) until aligned with opening. Depress button on motor flywheel. Presione el botón en la rueda del motor. Gire el anillo de bloqueo (1) hasta que esté alineado con la abertura. Insert blade assembly into slot. Inserte un montaje de paleta dentro de la ranura.
UL-ES-SilverdaleES-INSTALOC WH09 18 19 4 1 3 2 Rotate the flywheel in the same direction to next opened slot. Repeat previous step until all blades are installed. Rotate locking ring until button (1) engages locking ring. WARNING: Before returning power to fan, make sure button is fully engaging locking ring. 1 Unscrew and remove the finial (1), decorative cap (2), nut (3) and and rubber/ metal washer (4) from the bottom of the light kit. Install two bulbs (included).
UL-ES-SilverdaleES-INSTALOC WH09 20 Install glass (1) onto light kit and tighten rubber/metal washer (2) (rubber side facing the glass), and nut (3) onto bottom of glass. Make sure ceiling fan pull chain is threaded through the side hole in the bottom of the glass. Place decorative cap (4) over bottom of glass and secure by tightening decorative finial (5).
UL-ES-SilverdaleES-INSTALOC WH09 21 Once you have confirmed the operation of the fan, remove and discard red arrow sticker from the canopy. To install the canopy cover ring, peel the backing off the adhesive tape strips on the inside of the cover ring. Slide the cover ring up the downrod and secure to the canopy by gently pressing the adhesive tape to the bottom of the canopy. CAUTION!: Be careful and precise when attaching the canopy cover ring to the canopy.
UL-ES-SilverdaleES-INSTALOC WH09 For FLUSH MOUNT or EXTENDED DOWNROD Installation Para la instalación de MONTAJE AL RAS o con VARILLA VERTICAL MÁS LARGA 22 Remove keeper pin (1) from cross pin (2) in yoke on top of motor housing. Remove cross pin (2) and loosen set screws (3). (Do Not Remove Set Screws) 2 1 3 17 Separe el pasador de retención (1) del pasador transversal (2) en la horquilla en la parte superior del alojamiento del motor.
UL-ES-SilverdaleES-INSTALOC WH09 23 24 Slide canopy down to top of motor housing, exposing downrod ball assembly. Remove connector plug and green ground wire plug from canopy and unplug. Deslice el dosel hacia abajo hasta la parte superior del alojamiento del motor, hasta que el conjunto de la bola de la varilla vertical quede expuesto. Quite el enchufe conector y el enchufe del cable verde de tierra del dosel y desenchúfelos.
UL-ES-SilverdaleES-INSTALOC WH09 25 26 Loosen set screw in downrod ball. Slide down ball on downrod, exposing cross pin. Remove cross pin from downrod to allow wire plug to fit through downrod. Afloje el tornillo de fijación en la bola de la varilla vertical. Deslice hacia abajo la bola de la varilla vertical, exponiendo el pasador transversal. Quite el pasador transversal de la varilla vertical para permitir que el conector para cables pase a través de la varilla vertical.
UL-ES-SilverdaleES-INSTALOC WH09 27 1 Remove the canopy, downrod and ball from the motor housing yoke, feeding the plug and wires back through the top of the downrod. Remove the downrod and ball assembly from the canopy (1). Separe el dosel, la varilla vertical y la bola de la horquilla del alojamiento del motor, pasando el conector y los cables a través de la parte superior de la varilla vertical. Separe la varilla vertical y el conjunto de la bola del dosel (1).
UL-ES-SilverdaleES-INSTALOC WH09 28 Choose a MOUNTING OPTION Elija una OPCIÓN DE MONTAJE For FLUSH MOUNT INSTALLATION Para INSTALACIÓN AL RAS 29 FLUSH MOUNT OPTION If installing flush mount option, proceed to step 29. OPCIÓN DE INSTALACIÓN AL RAS Si está instalando el ventilador con la opción de montaje al ras siga con el paso 29. 1 EXTENDED DOWNROD OPTION If installing with longer downrod than supplied with fan, proceed to page 23, step 32.
UL-ES-SilverdaleES-INSTALOC WH09 31 30 Attach the multiwire plug connector as shown. Gather and push extra wiring back down into canopy, making sure wire plug connections are not broken. PROCEED TO STEP 10, PAGE 10. Attach canopy to motor housing using 3 flush mount screws and lock washers included in the hardware bag. Conecte el enchufe conector para varios cables como se indica.
UL-ES-SilverdaleES-INSTALOC WH09 For EXTENDED DOWNROD Installation Para instalación con VARILLA VERTICAL MÁS LARGA 33 32 1 Slide downrod ball (1) off of downrod supplied with fan. Deslice la esfera de la varilla vertical (1) hasta separarla de la varilla vertical incluida con el ventilador. Disconnect fan lead wires coming from the motor by unplugging 3 small wire plugs as shown.
UL-ES-SilverdaleES-INSTALOC WH09 34 1 3 2 4 Re-install pin (1) into extended downrod, and slide downrod ball (2) up to the top of the downrod. Re-install set screw to secure ball to downrod. Note: Some extended downrods have a pre-drilled set-screw hole. If a pre-drilled hole is present in the extended downrod, tighten the set screw into the pre-drilled hole in the extended downrod.
UL-ES-SilverdaleES-INSTALOC WH09 35 36 Push the black, white, and blue wires with small connectors thru the longer downrod and canopy from the downrod ball end. Pase los cables negro, blanco y azul con conectores pequeños a través de la varilla vertical más larga y el dosel comenzando en el extremo donde se encuentra la esfera de la varilla vertical. Find and add extra 60" lead wire using small plug connectors.
UL-ES-SilverdaleES-INSTALOC WH09 37 Connect plugs from downrod to plugs from fan, blue to blue, black to black, white to white. Conecte los conectores de la varilla vertical a los del ventilador, azul a azul, negro a negro y blanco a blanco.
UL-ES-SilverdaleES-INSTALOC WH09 38 Insert downrod into downrod yoke. Make sure to align hole in downrod with the hole in downrod yoke. Install yoke cross pin (1) through yoke and downrod. Insert keeper pin (2) into cross pin until it snaps into place. Tighten set screws (3) in yoke. 1 2 3 27 Inserte la varilla vertical en la horquilla de la varilla vertical. Asegúrese de que el orificio de la varilla vertical y el de la horquilla de la varilla vertical estén alineados.
UL-ES-SilverdaleES-INSTALOC WH09 39 40 Connect the multiwire plug connector as shown. Connect the green ground wire plug as shown. Gather and push extra wiring back down into canopy, making sure wire plug connections are not broken. PROCEED TO STEP 10, PAGE 10. Conecte el enchufe conector para varios cables como se indica. Conecte el cable verde de tierra como se indica. Recoja y empuje el cableado extra hacia abajo dentro del dosel, asegurándose de que los conectores de enchufe no estén rotos.
UL-ES-SilverdaleES-INSTALOC WH09 29