Instructions / Assembly

CEILING FAN LIGHT KIT
INSTALLATION AND SAFETY INSTRUCTIONS
We thank you for selecting one of our superior quality products. We dedicate
considerable time and effort to ensure they are the best available.
To ensure a successful installation be sure to read these instructions and review
the diagrams thoroughly before beginning. Follow the instructions that are
applicable for your light kit.
Ceiling fan light kits are only meant to be used with ceiling fans. Do not install
as a light fixture.
Caution – Risk of electrical shock. Before starting installation, disconnect the
power by turning off the circuit breaker or removing the fuse at the fuse box.
Turning the power off using the fan switch is not sufficient to avoid electrical
shock.
Review the installation instructions supplied with your fan. Make sure that your
fan has been wired properly into the ceiling to allow use with light kit.
All electrical connections must be in accordance with local codes, ordinances,
and national electric codes.
If you are unfamiliar with methods of installing electrical wiring, secure the
services of a qualified electrician.
NOTE: The important safeguards and instructions appearing in this manual are
not meant to cover all possible conditions and situations that may occur.
ALL SINGLE LIGHT KITS:
1-glassware or shade*
1-fitter with socket assembled
1-plastic bag containing:
-shade screws
-pull chain
-lock washer
-screw nut
-wire connectors
3 LIGHT KITS:
1-light fixture
3-light shades*
1-plastic bag containing:
-shade screws or socket rings
-pull chain
-lock washer
-screw nut
-wire connectors
*SOME LIGHT KITS MAY NOT INCLUDE GLASSWARE OR LIGHT SHADES.
PARTS
GENERAL
Figure 5
Figure 1
Figure 4
Figure 2
Figure 3
Figure 6
Figure 9a
Fan Switch
Housing
Cover
Plug
Screw
Fan Switch
Housing
Key Hole
Slot
Screw
Wire
Nuts
Fan
Light
Kit
Fan Switch
Housing
Key Hole
Slot
Screw
Wire
Nuts
Fan
Light
Kit
Adapter
Cup
Fan Switch
Housing
Cover
Screw
Plug
Adapter
Cup
Fan Light
Kit
Screw
Fan Switch
Housing
Screw
Wire
Nuts
Fan
Light
Kit
Canadian Wiring
Figure 7
Figure 8
Lock
Washer
Light
Fan
Kit
Light
Fan
Kit
Adapter
Hex Nut
Cup
Adapter
Cup
Fan Switch
Housing
Wire
Nuts
Threaded
Tube
Cover
Cover
Threaded
Tube
Hex Nut
Star Washer
Bushing
Fitter
Switch
Threaded Tube
Figure 12
CEILING FAN LIGHT KIT
INSTALLATION AND SAFETY INSTRUCTIONS
CEILING FAN LIGHT KIT
INSTALLATION AND SAFETY INSTRUCTIONS
Figure 10
Figure 11
Figure 9b
Screw
Shade
Fan
Switch
Housing
Bulb
Light Kit
Screw
Shade
Fan
Switch
Housing
Baffle
Figure 11
Shade
Socket
Ring
Fan
Switch
Housing
If light kit does not work, turn off electricity and lower either canopy or decorative hous-
ing on your ceiling fan to make sure the blue wire is connected to black household wire.
Please refer to electrical section on ceiling fan instruction manual.
1. If you want to replace the fitter for the fan
light kit, please loosen the hex nut and
bushing to release the fitter (See figure 12).
2. When
re-installing, please place the fitter ,
star washer over the threaded tube, then
tighten with hex nut. Take the switch through
th
e side hole of t he fitter then tighten with
the bushing. (See figure 12).
NOTE: For the white and brushed nickel finish
fitters, please use the brushed nickel finish
hardware; For the oil rubbed bronze fitter,
please use the antique brass finish hardware.
TROUBLESHOOTING
REPLACE FITTER INSTALLATION
Call 1-800-999-2226 or Fax [phone]
In Pacific and Mountain Time Zones
Call 1-800-421-3433 or Fax [phone]
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF
are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting.
All rights reserved. Made in China
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
www.westinghouselighting.com