ETL-ES-Comet-WH09 Owner's Manual Manual del usuario Comet TM Please write model number here for future reference: / Por favor, incluya el número del modelo aquí para futura referencia: Net Weight: 17.64 LBS Peso Neto: 8.
ETL-ES-Comet-WH09 Safety tips OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT TO OUTLET BOX MARKED "ACCEPTABLE FOR FAN SUPPORT", AND USE THE OUTLET SCREWS PROVIDED WITH THE OUTLET BOX. MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF LIGHTING FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND MAY NEED TO BE REPLACED. CONSULT A QUALIFIED ELECTRICIAN IF IN DOUBT. 1.
ETL-ES-Comet-WH09 Consejos de seguridad HAGA LO SIGUIENTE: LEA Y GUARDE ESTAS INSTRUCCIONES ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELÉCTRICA O LESIONES PERSONALES, MONTE EL VENTILADOR EN UNA CAJA DE EMBUTIR ROTULADA “ADECUADA PARA VENTILADORES”, Y UTILICE LOS TORNILLOS DE MONTAJE INCLUIDOS CON LA CAJA DE EMBUTIR. LA MAYORÍA DE LAS CAJAS DE EMBUTIR UTILIZADAS NORMALMENTE PARA ARTEFACTOS DE ILUMINACIÓN NO SON ADECUADAS PARA VENTILADORES Y DEBERÍAN SER REEMPLAZADAS.
ETL-ES-Comet-WH09 Features Características FLUSH MOUNT INSTALLATION INSTALACIÓN AL RAS DOWNROD INSTALLATION instalación con varilla vertical VAULTED CEILING INSTALLATION INSTALACIÓN PARA CIELORRASOS ABOVEDADOS COMBO-BLADE For low ceilings Para cielorrasos bajos For normal ceilings Para cielorrasos normales May require a longer downrod (sold separately) Podría requerir una varilla vertical más larga (se vende por separado) Combo-Blades feature two high quality finishes on one blade.
ETL-ES-Comet-WH09 pREPARING for installation Antes de la instalación 1 2 Unpack and inspect fan carefully to be certain all contents are included. Turn off power at fuse box to avoid possible electrical shock. Use metal outlet box suitable for fan support (must support 35 lbs). Before attaching fan to outlet box, ensure the outlet box is securely fastened by at least two points to a structural ceiling member (a loose box will cause the fan to wobble).
ETL-ES-Comet-WH09 Mounting bracket Installation Instalación con soporte de montaje 3 1 2 1 2 Remove the screws and star washers from the two mating holes (1) on the canopy. Loosen (do not remove) the screws in the mating slots (2) on the canopy. Rotate the mounting bracket counter-clockwise and remove from the canopy. Quite los tornillos y las dos arandelas en estrella de los dos orificios coincidentes (1) del dosel. Afloje (no quite) los tornillos de las ranuras coincidentes (2) del dosel.
ETL-ES-Comet-WH09 MOUNTING OPTIONS OPCIONES DE MONTAJE Mounting bracket Installation Instalación con soporte de montaje 5 4 Choose a MOUNTING OPTION Elija una OPCIÓN DE MONTAJE FLUSH MOUNT OPTION If flush mount option is selected, proceed to page 8, step 6. OPCIÓN DE INSTALACIÓN AL RAS Si elige la opción de montaje al ras, proceda a la página 8, paso 6. NORMAL DOWNROD OPTION If installing downrod supplied with fan, proceed to page 9, step 8.
ETL-ES-Comet-WH09 FLUSH MOUNT OPTION OPCIÓN DE INSTALACIÓN AL RAS 7 6 For flush mount option, raise fan assembly and place onto hook from mounting bracket into a closed hole on the canopy. This will allow for hands free wiring. PROCEED DIRECTLY TO PAGE 13 FOR WIRING OPTIONS. Para la opción de montaje al ras, levante el montaje del ventilador, colóquelo sobre el gancho de la placa de montaje y cuélguelo en uno de los agujeros cerrados del dosel.
ETL-ES-Comet-WH09 NORMAL DOWNROD OPTION OPCIÓN CON VARILLA VERTICAL PARA CIELORRASO NORMAL 8 EXTENDED DOWNROD OPTION OPCIÓN CON VARILLA VERTICAL MÁS LARGA 9 2 3 3 1 Feed motor lead wires through downrod/canopy assembly and insert downrod into downrod yoke. Make sure to align hole in downrod with the hole in downrod yoke. Install yoke cross pin (1) through yoke and downrod. Insert clamp pin (2) into cross pin until it snaps into place. Tighten set screws (3) in yoke. PROCEED TO PAGE 12, STEP 13.
ETL-ES-Comet-WH09 EXTENDED DOWNROD OPTION OPCIÓN CON VARILLA VERTICAL MÁS LARGA 10 2 1 Slide downrod ball (1) off of downrod and remove pin (2). Deslice la esfera de la varilla vertical (1) hasta separarla de la varilla vertical y quite el pasador (2). 11 Re-install pin into extended downrod, and slide downrod ball up to the top of the downrod. Re-install set screw to secure ball to downrod. Note: Some extended downrods have a pre-drilled set-screw hole.
ETL-ES-Comet-WH09 EXTENDED DOWNROD OPTION OPCIÓN CON VARILLA VERTICAL MÁS LARGA 12 2 3 1 Feed motor lead wires through downrod/canopy assembly and insert downrod into downrod yoke. Make sure to align hole in downrod with the hole in downrod yoke. Install yoke cross pin (1) through yoke and downrod. Insert clamp pin (2) into cross pin until it snaps into place. Tighten set screws (3) in yoke.
ETL-ES-Comet-WH09 MOUNTING MONTAJE 13 14 2 1 Carefully lift fan assembly onto mounting bracket. Rotate fan until notch on downrod ball (1) engages the ridge on the mounting bracket (2). This will allow for hands free wiring. Levante con cuidado el conjunto del ventilador hasta el soporte de montaje. Gire el ventilador hasta que la muesca de la bola de la varilla vertical (1) calce sobre la saliente del soporte de montaje (2). De este modo, tendrá las dos manos libres para hacer el cableado.
ETL-ES-Comet-WH09 wiring OPTIONS OPCIÓN DE CABLEADO 15 PULL CHAIN WIRING OPTION From Fan: White (common) Black (hot) Blue* (hot) Main (ground) (connect) (connect) (connect) 16 From House: White (common) Black (hot) Green (ground) WALL CONTROL WIRING OPTION From Fan: White (common) Black (hot) Blue* (hot) Main (ground) *Attach blue wire only if attaching light kit with fan. (conectar) Wall Control Follow diagram above to make wiring connections for wall control operation.
ETL-ES-Comet-WH09 Secure To Ceiling Asegure el ventilador al cielorraso 17 For flush mount fans, carefully lift fan from the mounting bracket, making sure not to break any wire connections. For downrod fans, slide the canopy up to the mounting bracket. Para ventiladores de instalación al ras, levante con cuidado el ventilador del soporte de montaje asegurándose de que no interrumpa ninguna conexión de los cables.
ETL-ES-Comet-WH09 Blade Installation Instalación de las paletas 18 2 4 19 1 3 2 1 Check the motor for plastic shipping stabilizer tabs (1), and remove them if they are present. Attach blade assembly to motor using the noise-dampening motor gaskets (2) and motor screws provided. Tighten screws securely. NOTE: Some models do not utilize motor gaskets, washers, or stabilizer tabs. Verifique si hay lengüetas plásticas de embalaje para sostener al motor (1) y descártelas.
ETL-ES-Comet-WH09 Light fixture installation Instalación del artefacto luminoso 20 Attach the molex plug from the fan to the molex from the light kit and attach the light kit to the switch housing plate using screws provided. Conecte los conectores molex del ventilador al conector molex del artefacto luminoso y asegure el artefacto luminoso a la placa del alojamiento del interruptor usando los tornillos incluidos. 21 22 Install light bulbs (included). Instale las bombillas de luz (incluidas).
ETL-ES-Comet-WH09 23 Assemble decorative fob and extension chains from hardware bag to fan pull chains by inserting end of chain into chain coupling. Confirm chains are held by lightly pulling both chains in coupling. Sujetar las cadenas largas de tiro con las piezas finales correspondientes, a las cadenas del ventilador, introduciendo el extremo de la cadena larga en la pieza de unión. Asegúrese de que las cadenas están bien sujetas, tirando ligeramente de ambas cadenas en la pieza de unión.
ETL-ES-Comet-WH09 OPERATION AND MAINTENANCE Operation Turn on the power and check operation of fan. The pull chain controls the fan speeds as follows: 1 pull - high; 2 pulls - medium; 3 pulls - low; 4 pulls - off. Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans and so on. The slide switch controls direction, forward or reverse. Warm weather - (Forward) Fan turns counterclockwise direction.
ETL-ES-Comet-WH09 Operación y mantenimiento Operación Encienda el ventilador y verifique su funcionamiento. La cadenilla de tiro controla las velocidades del ventilador de la siguiente manera: 1 jalón – rápida; 2 jalones - mediana; 3 jalones - lenta; 4 jalones - apagado. Las velocidades para clima cálido o frío dependen de factores como el tamaño de la habitación, la altura del ventilador, el número de ventiladores, etc. El conmutador de tipo deslizante controla la dirección, hacia adelante o hacia atrás.
ETL-ES-Comet-WH09 Troubleshooting guide If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble Shooting Chart. If a problem cannot be remedied, please consult with your authorized electrician and do not attempt any electrical repairs yourself. TROUBLE SUGGESTED REMEDY 1. If fan does not start: 1.
ETL-ES-Comet-WH09 Guía para solucionar problemas Si tiene dificultades para hacer funcionar su nuevo ventilador, podría ser a causa del armado, instalación o cableado incorrectos. En algunos casos, estos errores de instalación podrían ser confundidos con defectos. Si experimenta alguna falla, consulte esta guía para solucionar problemas. Si no puede solucionar el problema, consulte a un electricista autorizado y no intente reparar conexiones eléctricas. PROBLEMA SOLUCIÓN SUGERIDA 1.
ETL-ES-Comet-WH09 22
ETL-ES-Comet-WH09 PARTS LIST LISTA DE REPUESTOS # Description 1.................. 2.................. 3.................. 4.................. 5.................. 6.................. 7.................. 8.................. 1 Mounting Bracket Blade Bracket Blade Glass Fan Speed Switch Light Control Switch Capacitor Hardware Pack 3 2 No. Descripción 1.................. 2.................. 3.................. 4.................. 5.................. ................... 6.................. 7..............
ETL-ES-Comet-WH09 Westinghouse Lighting Corporation 12401 McNulty Road Philadelphia, PA 19154 U.S.A. Westinghouse Lighting Corporation 12401 McNulty Road Philadelphia, PA 19154 U.S.A.