Installation Guide

ManualsBrandsWestinghouse ManualsKitchenSparta 52 in. Indoor Brushed Nickel Finish Ceiling Fan

ETL-ES-Sparta-WH10

Remove clamp pin (O) and cross pin (P) from downrod (J).

Quite el pasador tipo prensa (O) desde el pasador transversal (P) de la vara (J).

INSTALLATION

INSTALACIÓN

Unpack and inspect fan carefully to be certain all

contents are included.

Quite el envoltorio e inspeccione detenidamente el ventilador para verifi-

car que todas las piezas estén incluidas.

Use metal outlet box suitable for fan support (must support 35 lbs).

Before attaching fan to outlet box, ensure the outlet box is securely

fastened by at least two points to a structural ceiling member (a loose

box will cause the fan to wobble).

Turn off power at fuse box to avoid possible

electrical shock.

Apague la alimentación en la caja de

fusibles para evitar la posibilidad de descarga eléctrica.

Use una caja de embutir de metal adecuada para soportar un ventilador

(debe soportar 35 libras). Antes de fijar el ventilador a la caja de embutir

asegúrese de que la misma esté fijada de manera segura en por lo menos

dos puntos a un miembro estructural del cielo raso (una caja suelta haría

que el ventilador oscile).

Install mounting bracket (G) to outlet box in ceiling using the screws and

washers provided with the outlet box.

Instale el soporte de montaje (G) a la caja de embutir del cielorraso con la

tornillería suministrada con la caja de embutir.

Summary of content (10 pages)

PAGE 1
INSTALLATION INSTALACIÓN 1 Unpack and inspect fan carefully to be certain all contents are included. Quite el envoltorio e inspeccione detenidamente el ventilador para verificar que todas las piezas estén incluidas. Turn off power at fuse box to avoid possible electrical shock. Apague la alimentación en la caja de fusibles para evitar la posibilidad de descarga eléctrica. 2 Use metal outlet box suitable for fan support (must support 35 lbs).
PAGE 2
Choose a mounting option / Elija una opción de montaje: 5 6 NORMAL DOWNROD INSTALLATION - If installing downrod supplied with fan, proceed to step 6. EXTENDED DOWNROD INSTALLATION - If installing with longer downrod than supplied with fan, proceed to step 8. NORMAL -Si instala la varilla vertical incluida con el ventilador, proceda al paso 6. OPCIÓN CON VARILLA VERTICAL MÁS LARGA - Si instala una varilla vertical más larga que la que se incluye con el ventilador, proceda al paso 8.
PAGE 3
Re-install pin (Q) into extended downrod, and slide downrod ball (I) up to the top of the downrod. Re-install set screw (S) to secure ball to downrod. Note: Some extended downrods have a pre-drilled set-screw hole. If a pre-drilled hole is present in the extended downrod, tighten the set screw into the pre-drilled hole in the extended downrod. If no pre-drilled hole exists in the extended downrod, tighten the set screw against the downrod to secure the downrod ball. PROCEED TO STEP 6.
PAGE 4
12 This remote control unit is equipped with 16 code combinations to prevent possible interference from or to other remote units. The frequency switches on your receiver (N) and transmitter (M) have been preset at the factory. Please recheck to make sure the switches on transmitter (M) and receiver (N) are set to the same position, any combination of settings will operate the fan as long as the transmitter and receiver are set to the same position.
PAGE 5
15 The inside canopy cover ring (H) has two keyhole slots that allow it to be mounted onto the screw heads on the two protruding screws from the mounting bracket. Slide the canopy cover ring up the downrod, and allow the two protruding screw heads from the mounting bracket to go into the keyhole slots on the canopy cover ring. Once engaged, twist the canopy cover ring to lock it onto the screw heads.
PAGE 6
B C 17 Insert the blade (C) through the slot on the flywheel (B). Make sure blade holes and holes on the flywheel are aligned. Secure the blade to the flywheel using blade screws (V) and metal washers (AA) provided. Repeat this step for remaining blade. Tighten screws securely. V Inserte la paleta (C) a través de la ranura en la rueda (B). Asegúrese de que los agujeros de la paleta y los de la rueda estén alineados.
PAGE 7
A 20 Connect the wire plugs from the motor (A) to the wire plugs from the light kit (D), white to white, and black to black. Conecte los conectores para cables del motor (A) a los conectores para cables del juego de luces (D) blanco a blanco y negro a negro. D Attach the light kit (D) to the light kit plate by placing the keyslot holes from the light kit onto the two protruding screw heads from the light kit plate. Twist the light kit until the screwheads engage the keyslots.
PAGE 8
Install E11 base, max 100W bulb (CC) (included). Caution: Do not touch glass part of bulbs with bare hands. 22 Instale las bombilla (CC) de base E11 de un máximo de 100 vatios (se incluyen). Advertencia: No toque la parte de vidrio de las lámparas directamente con las manos. CC 23 Locate the indentations on the neck of the glass (E) and align with the protrusions from the light kit (D).
PAGE 9
24 Mount wall bracket to the wall using screws provided. Instale el soporte de pared sobre la pared con los tornillos incluidos. Place the transmitter into the mounted holder. 25 Coloque el transmisor en el soporte montado. Remote Control Operation 1. Fan Control– press and release. The remote control operates the fan speed as follows: 1 - high; 2 - medium; 3 – low; 0 - off. 2. Light On/Off – press and release light button. 3.
PAGE 10
NOTICE This ‘Energy Policy Act 2005’ compliant fan includes a device that limits the total wattage of its light fixture to 190 watts. By installing a combination of light bulbs that exceeds 190 watts or if an electrical surge causes the wattage to exceed 190 watts, the light fixture will either dim the lights to 190 watts or will automatically turn off.