Owner’s Manual LED Outdoor Lighting Fixture Installation Instructions W-373 120513 Please write model number here for future reference: / Veuillez noter le numéro de modèle aux fins de référence ultérieure: / Por favor, incluya el número del modelo aquí para futura referencia:
ASSEMBLY INSTRUCTIONS FOR OUTDOOR LIGHT FIXTURE Congratulations on yourWestinghouse purchase. This fixture has been designed to give you many years ofbeautyand service. For questions and comments, please visit www.westinghouselighting. com/contact-us. NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any packing materials (see figure 1).
FIGURE 1. *OUTLET BOX (C) CROSS BAR (B) SIDE HOLE (G) *OUTLET BOX SCREWS (D) MOUNTING SCREWS (A) BACK PLATE (H) GROUND WIRE GREEN GROUNDING SCREW (F) WIRE CONNECTORS (E) CAP NUTS (I) Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture.
MOUNTING AND WIRING INSTRUCTIONS CAUTION: For fixtures labeled for outdoor and wet location use, provide a water-tight seal between the fixture and the mounting surface by using silicone or similar caulking. NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures meet all UL specifications. 1. Turn off power at fuse box to avoid possible electric shock. 2.
LES INSTRUCTIONS D'ASSEMBLAGE DE L'APPAREIL D'ÉCLAIRAGE POUR UTILISATION EXTÉRIEURE Félicitations ! Vous avez acheté un produit de Westinghouse Lighting. Cet appareil d'éclairage a été conçu pourdurerde nombreuses années. Si vous avez des questions ou des commentaires à nous communiquer, veuillez visiter www.westinghouselighting.com/contact-us. NOTA : Déballez soigneusement l'appareil d'éclairage et les pièces. Assurez-vous que toutes les pièces y sont avant de mettre l’emballage au rebut (voir fig. 1).
FIGURE 1. BARRE TRANSVERSALE (B) *BOITE DE SORTIE DE COURANT (C) *VIS DE LA BOITE DE SORTIE DE COURANT (D) TROU LATERAL (G) VIS DE FIXATION (A) PLAQUE ARRIERE (H) FIL DE MISE A LA TERRE VIS DE MISE A LA TERRE (VERTE) (F) CONNECTEURS DE FIL (E) ECROUS CAPUCHONS (I) Il est possible que le dessin illustré ici ne soit pas la reproduction exacte de l’appareil d’éclairage contenu dans la boîte. Les instructions d’installation demeurent cependant valables.
INSTRUCTIONS DE MONTAGE ET DE RACCORDEMENT NOTA : Underwriters Laboratories (UL) n’exige pas que tous les appareils d’éclairage comportent des fils de mise à la terre. Ces appareils satisfont cependant à toutes les spécifications UL. 1. Mettez l’interrupteur de la boîte à fusibles à « OFF » afin d’éviter le risque d’électrocution. 2.
INSTRUCCIONES DE MONTAJE PARA EL ARTEFACTO DE ILUMINACIÓN PARA EXTERIORES Le felicitamos porcomprareste producto de Westinghouse Lighting. Este producto ha sido diseñado para brindarle muchos años de belleza yservicio. Si tiene preguntas y comentarios, visite por favor www.westinghouselighting.com/contact-us. NOTA: Extraiga cuidadosamente el artefacto y las piezas. Verifique que contenga todas las partes requeridas (consulte la figura 1) antes de descartar los materiales de empaque.
FIGURA 1. BARRA TRANSVERSAL (B) *CAJA DE EMBUTIR (C) ORIFICIO LATERAL (G) *TORNILLOS CAJA DE EMBUTIR (D) TORNILLOS DE MONTAJE (A) PLACA POSTERIOR (H) CABLE DE TIERRA TORNILLO VERDE DE TIERRA (F) CONECTORES DE ROSCA (E) TUERCAS TAPA (I) Los dibujos pueden no coincidir exactamente con el artefacto incluido. Sin embargo, las instrucciones de instalación se aplican a este artefacto.
INSTRUCCIONES DE MONTAJE Y CABLEADO NOTA: Underwriters Laboratories (U.L.) no requiere que todos los artefactos tengan cables de tierra. Estos artefactos cumplen con todas las especificaciones U.L. 1. Apague la alimentación en la caja de fusibles para evitar la posibilidad de descarga eléctrica. 2. Enrosque los tornillos de montaje (A) en la placa de barra tranvsversal (B) con los tornillos de montaje sobresaliendo de la caja de embutir (C) (vea la figura 1). 3.
FIGURE 2. GROUP A: CONNECT TO BLACK HOUSE WIRE GROUP B: CONNECT TO WHITE HOUSE WIRE BLACK WHITE WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER BROWN, GOLD OR BLACK WITHOUT TRACER BROWN, GOLD OR BLACK WITH TRACER NOTE: When parallel wire (SPT 1 & SPT 2) is used; the neutral wire is square shaped and ridged, and the hot wire will be round in shape and smooth. (See below.) WARNING Turn off electricity to the mounting site before beginning installation.
CLEANING AND CARE To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can discolor the finish of fixture. Extend-A-Finish Laquer Conditioner, Item#70295, is recommended once a year to clean, condition, and protect fixture. Do not use scouring pads, powders, steel wool or abrasive paper to clean this fixture.