UL-ES-I56/W-WH06 Owner's Manual Manual del usuario Industrial Please write model number here for future reference: / Por favor, incluya el número del modelo aquí para futura referencia: Net Weight: Peso Neto: 9.7 LBS 4.
UL-ES-I56/W-WH06 Safety tips OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT TO OUTLET BOX MARKED "ACCEPTABLE FOR FAN SUPPORT", AND USE THE OUTLET SCREWS PROVIDED WITH THE OUTLET BOX. MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF LIGHTING FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND MAY NEED TO BE REPLACED. CONSULT A QUALIFIED ELECTRICIAN IF IN DOUBT. 1.
UL-ES-I56/W-WH06 Consejos de seguridad HAGA LO SIGUIENTE: LEA Y GUARDE ESTAS INSTRUCCIONES 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELÉCTRICA O LESIONES PERSONALES, MONTE EL VENTILADOR EN UNA CAJA DE EMBUTIR ROTULADA “ADECUADA PARA VENTILADORES”, Y UTILICE LOS TORNILLOS DE MONTAJE INCLUIDOS CON LA CAJA DE EMBUTIR.
UL-ES-I56/W-WH06 pREPARING for installation Antes de la instalación 1 2 Unpack and inspect fan carefully to be certain all contents are included. Turn off power at fuse box to avoid possible electrical shock. Use metal outlet box suitable for fan support (must support 35 lbs). Before attaching fan to outlet box, ensure the outlet box is securely fastened by at least two points to a structural ceiling member (a loose box will cause the fan to wobble).
UL-ES-I56/W-WH06 Mounting bracket Installation Instalación con soporte de montaje 3 2 1 2 1 Remove the screws and star washers from the two mating holes (1) on the canopy. Loosen (do not remove) the screws in the mating slots (2) on the canopy. Rotate the mounting bracket and remove from the canopy. Quite los tornillos y las dos arandelas en estrella de los dos orificios coincidentes (1) del dosel. Afloje (no quite) los tornillos de las ranuras coincidentes (2) del dosel.
UL-ES-I56/W-WH06 Mounting bracket Installation Instalación con soporte de montaje MOUNTING OPTIONS OPCIONES DE MONTAJE 4 5 Choose a MOUNTING OPTION Elija una OPCIÓN DE MONTAJE NORMAL DOWNROD OPTION If installing downrod supplied with fan, proceed to page 9, step 9. OPCIÓN CON VARILLA VERTICAL PARA CIELORRASO NORMAL Si instala la varilla vertical incluida con el ventilador, proceda a la página 9, paso 9.
UL-ES-I56/W-WH06 EXTENDED DOWNROD OPTION OPCIÓN CON VARILLA VERTICAL MÁS LARGA 6 7 3 2 1 2 1 Slide downrod ball (1) off of downrod and remove pin (2). Deslice la esfera de la varilla vertical (1) hasta separarla de la varilla vertical y quite el pasador (2). Loosen downrod ball (1) from downrod (2) by removing set screw (3). Afloje la esfera de la varilla vertical (1) de la varilla vertical (2) quitando el tornillo (3).
UL-ES-I56/W-WH06 EXTENDED DOWNROD OPTION OPCIÓN CON VARILLA VERTICAL MÁS LARGA 8 Re-install pin into extended downrod, and slide downrod ball up to the top of the downrod. Re-install set screw to secure ball to downrod. Note: Some extended downrods have a pre-drilled set-screw hole. If a pre-drilled hole is present in the extended downrod, tighten the set screw into the pre-drilled hole in the extended downrod.
UL-ES-I56/W-WH06 10 9 3 5 4 1 2 1 Thread leadwires through the downrod and install crosspin (1) through yoke (2) and downrod. Install lockwasher (3) and nut (4) and tighten. Install cotter pin (5). Loosen set screws on the lower canopy (1). Install canopies onto downrod as shown. Thread lead wires through the downrod. Instale el pasador transversal (1) a través de la grapa (2) y el eje central. Instale la arandela de seguridad (3) y la tuerca (4). Aprete e instale la clavija hendida(5).
UL-ES-I56/W-WH06 MOUNTING MONTAJE 11 12 Loosen set screw in lower canopy and slide to within 1/4” of the motor. Tighten set screw(s) in the lower canopy. Make sure there is at least 1/4” clearance maintained around the motor and lower canopy. Carefully lift fan assembly onto mounting bracket. Rotate fan until notch on downrod ball (1) engages the ridge on the mounting bracket (2). This will allow for hands free wiring. Levante con cuidado el conjunto del ventilador hasta el soporte de montaje.
UL-ES-I56/W-WH06 MOUNTING MONTAJE wiring OPTIONS OPCIÓN DE CABLEADO 14 13 WALL CONTROL WIRING OPTION From Fan: White (common) Black (hot) Blue* (hot) Main (ground) (connect) (connect) (connect) (connect) From House: White (common) Fan Switch (hot) Light Switch (hot) Green (ground) Wall Control *Attach blue wire only if attaching light kit with fan. Follow diagram above to make wiring connections for wall control operation.
UL-ES-I56/W-WH06 Secure To Ceiling Asegure el ventilador al cielorraso 15 For flush mount fans, carefully lift fan from the mounting bracket, making sure not to break any wire connections. For downrod fans, slide the canopy up to the mounting bracket. Para ventiladores de instalación al ras, levante con cuidado el ventilador del soporte de montaje asegurándose de que no interrumpa ninguna conexión de los cables.
UL-ES-I56/W-WH06 Blade Installation Instalación de las paletas 16 3 Install blades to top of motor using screws and washers . See above drawing for reference. Instale las paletas en la parte superior del motor con la tornillería. Utilice la ilustración anterior como referencia.
UL-ES-I56/W-WH06 Installing and wiring the wall control Instalación y cableado del control de pared and wiring the wall control. 17 Installing A. Remove the cross bar screws (2) from the wall control and attach the cross bar(3) to the outlet box. B. C. D. E. Remove front panel screw (8). Save for use in step E. Remove front cover (7). WARNING: PLEASE USE CAUTION WHEN REMOVING THE FACE PLATE COVER.
UL-ES-I56/W-WH06 Installing and wiring the wall control Instalación y cableado del control de pared Parts: Piezas: 1. Outlet box 2. Cross Bar Screws 3. Cross Bar 4. Outlet Box Screws 5. Control Unit 6. Terminal Box 7. Front Panel 8. Front Panel Screw 9. Terminal Box Screw 10. Black Supply Lead Wire 11. Black Fan Lead Wire 12. Ground Lead Wire 1. Caja de embutir 2. Tornillos de la barra transversal 3. Barra transversal 4. Tornillos de la caja de embutir 5. Unidad de control 6. Caja de terminales 7.
UL-ES-I56/W-WH06 OPERATION AND MAINTENANCE Operation Turn on the power and check operation of fan. The pull chain controls the fan speeds as follows: 1 pull - high; 2 pulls - medium; 3 pulls - low; 4 pulls - off. Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans and so on. Maintenance 1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year.
UL-ES-I56/W-WH06 Operación y mantenimiento Operación Encienda el ventilador y verifique su funcionamiento. La cadenilla de tiro controla las velocidades del ventilador de la siguiente manera: 1 jalón – rápida; 2 jalones - mediana; 3 jalones - lenta; 4 jalones - apagado. Las velocidades para clima cálido o frío dependen de factores como el tamaño de la habitación, la altura del ventilador, el número de ventiladores, etc. Mantenimiento 1.
UL-ES-I56/W-WH06 18
UL-ES-I56/W-WH06 PARTS LIST LISTA DE REPUESTOS 1 # Description 1.................. 2.................. 3.................. 8.................. Mounting Bracket Blade Wall Control Hardware Pack 2 No. Descripción 1.................. 2.................. 3.................. 8..................
UL-ES-I56/W-WH06 Westinghouse Lighting Corporation 12401 McNulty Road Philadelphia, PA 19154 U.S.A. Westinghouse Lighting Corporation 12401 McNulty Road Philadelphia, PA 19154 U.S.A.
