Installation Guide

ManualsBrandsWestinghouse ManualsAll Fridges340L Bottom Mount Fridge

IK007 Integration kit

Installation manual

Refrigeration

STM3900, STM4200, SBM3800, SBM4300,

WTM2800, WTM3000, WTM3300, WTM3900,

WTM4200, WTM4400, WTM5200, WTE4200,

WTE5200, WTB2300, WTB2500, WTB2800,

WTB3400, WTB3700, WBM3700, WBM3800,

WBM4000, WBM4300, WBM5100, WBE4300,

WBE5100, WRM3700, WRM4300,WFM3000,

WFM3600, KTM2800, KTM3000, KTM3300,

KTM3600, KTM3900, KTM4200, KTM4400,

KTM5200, KBM3800, KBM4300, KBM5100,

WBB3400, WBB3700

Summary of content (16 pages)

PAGE 1
IK007 Integration kit Installation manual Refrigeration STM3900, STM4200, SBM3800, SBM4300, WTM2800, WTM3000, WTM3300, WTM3900, WTM4200, WTM4400, WTM5200, WTE4200, WTE5200, WTB2300, WTB2500, WTB2800, WTB3400, WTB3700, WBM3700, WBM3800, WBM4000, WBM4300, WBM5100, WBE4300, WBE5100, WRM3700, WRM4300,WFM3000, WFM3600, KTM2800, KTM3000, KTM3300, KTM3600, KTM3900, KTM4200, KTM4400, KTM5200, KBM3800, KBM4300, KBM5100, WBB3400, WBB3700
PAGE 2
CONGRATULATIONS Congratulations and thank you for choosing our integration kit. Before you install the integration kit, we recommend that you read through the entire installation manual. To avoid the risks that are always present when you install an electrical appliance, it is important that the integration kit and appliance is installed correctly. Please read the safety instructions in this installation manual as well as the appliance’s user manual to carefully to avoid misuse and hazards.
PAGE 3
GENERAL WARNINGS lease read the user manual carefully and store in a P handy place for later reference. Pass the user manual on to possible new owners of the appliance. NOTE: We strongly recommend that a professional builder/cabinetmaker builds this unit into required cabinetry prior to finished installation in customer’s kitchen. Electrolux cannot take responsibility for any installation issues when customer retrofits this product into cabinetry.
PAGE 4
REFRIGERATOR INTEGRATION KIT ITEMS Because this kit is common to a variety of models, you need to select the items required to suit your model. The items required for the models covered in this instruction booklet are shown below. Those items not required on your particular model should be discarded.
PAGE 5
CUPBOARD DIMENSIONS IMPORTANT! Pages 5, 6, 7 and 8 should be given to the person responsible for cupboard design and construction. The cupboard dimensions required for each model are shown on page 6, 7 & 8. 1. All sizes are internal and measured in millimetres. 2. It is important to ensure that the correct cupboard sizes are used to ensure adequate air flow around the refrigerator. 3. Cupboard hinges should be a 120° opening type. (Use hinges supplied). 4.
PAGE 6
CUPBOARD DIMENSIONS NOTE: All sizes are internal and measured in millimetres. For ‘lettered’ dimensions refer to the table on page 5.
PAGE 7
CUPBOARD DIMENSIONS Clearances Airflow When installed the refrigerator needs to have adequate air ventilation. It is important to ensure there is good airflow from the front to underneath and up the rear to the top of the cabinet (see diagrams). Front airflow cut-out 50mm Dim E Front airflow cut-out NOTE: A decorative grill can be fitted so long as it does not obstruct airflow and is removable for cleaning.
PAGE 8
120° hinge CUPBOARD DIMENSIONS INSTALLATION OF 120˚ HINGE When positioned in a corner the clearance of Dim G on the hinge side of the cabinet will allow the doors to be opened enough to enable the removal of the crisper bins. Dim C Please follow the instructions below to install the 120º hinge. Dim G mounting plate 120° 120° hinge Attach mounting plate with 120º hinge and tighten the screw. NOTE: Use the 120° hinges supplied with the kit to attach the cupboard door to the cupboard.
PAGE 9
PREPARATION ATTACHING THE TOP HINGE BRACKET 1. Unpack refrigerator, removing foam packing. 2. Lay the refrigerator down on its back on a piece of soft packing material. Use caution and two people while laying the appliance down. 3. Remove top door stopper if fitted (Figure 1). 4. Place adjustable rollers in the fully retracted position by screwing height adjusting screw fully anti-clockwise (Figure 2). Do not remove the adjusting nut completely. 5. Stand upright. Figure 1 1.
PAGE 10
ATTACHING SLIDE-HOUSING TO REFRIGERATOR DOORS 1. Ensure slide-housing is positioned squarely as shown. 2. Ensure that the slide-housing is positioned on the door as shown in the diagrams. slide housing protruding edge Note: The slide-housing ‘protruding edge’ side must always be closest to the door handle side (diagram right). 70mm door handle 360mm 70mm 235mm 235mm 235mm 70mm 235mm 70mm 2 door bottom freezer 2 door top freezer ...and secure with tape.
PAGE 11
NOTE: For single door models, the door handle must be completely removed to provide clearance to the cupboard door and the resulting handle mounting holes hidden with a cover. Installer must use a tape or plastic cover that suits the installation appearance (not supplied). 3. While the slide-housing is taped in position, punch a small hole in the refrigerator door skin corresponding to the four (4) holes in the housing (Figure 5). 4.
PAGE 12
PLACING REFRIGERATOR IN CUPBOARD REFRIGERATOR ALIGNMENT 1. Ensure cupboard is level and square. 2. Put refrigerator into cupboard. Use caution and two people if necessary. 3. Insert slide bars into slide-housings (Figure 7). NOTE: Ensure the refrigerator is level in the cupboard. Raise the front of the refrigerator by using the height adjusting screws. Figure 7 Position the refrigerator in the cupboard so that: 1. Top hinge bracket is against cupboard wall (Figure 8). 2.
PAGE 13
SECURING THE REFRIGERATOR IN THE CUPBOARD 4. Slowly close the cupboard door (pushing the refrigerator back) until it is slightly ajar, i.e. with a gap of about 4mm (Figure 11). NOTE: When attaching all screws to cupboard, first drill a 2mm pilot hole in the correct position. This will allow easy hand insertion of self tapping screw. You may have to reposition the refrigerator back or forward until the 4mm gap is obtained. Ensure that the refrigerator remains parallel as you do this.
PAGE 14
ATTACHING SLIDE-BAR TO THE CUPBOARD DOOR 1. Fully open cupboard door (120°). 2. Open refrigerator door until it rests against the cupboard door. 3. Position slide-bar in slide-housing so that all three holes are visible when both doors are fully open (120°). This position is typically 125mm from the edge of the cupboard door (Figure 14). Figure 14 120º cupboard door refrigerator door Whilst slide-bar is still in housing: 4.
PAGE 15
Figure 19 Figure 20 Figure 21 REPEAT THIS PROCEDURE FOR THE SECOND SLIDE BAR IF NECESSARY. THIS COMPLETES THE INSTALLATION PROCEDURE. CUSTOMERS PLEASE NOTE: In the unlikely event service is required on an integrated refrigerator during the warranty period, it is the customer’s responsibility to remove the refrigerator from the cupboard. Removal of the refrigerator from the cupboard is not covered by warranty.
PAGE 16
Electrolux Home Products Australia telephone: 1300 363 640 fax: 1800 350 067 email: customercare@electrolux.com.au web: www.electrolux.com.au Electrolux Home Products New Zealand telephone: 0800 234 234 fax: 0800 363 600 email: customercare@electrolux.co.nz web: www.electrolux.co.nz The Thoughtful Design Innovator.