USER MANUAL INSTRUCTIONS DOOR REVERSAL KIT WRB5004S, WRB5004W WFB4204S, WFB4204W
GENERAL WARNINGS lease read the installation manual carefully and store P in a handy place for later reference. Pass the installation manual on to possible new owners of the appliance. Read the following carefully to avoid damage or injury. NOTE: You must read these warnings carefully before installing or using the accessory. If you need assistance, contact your Customer Care Department.
KIT CONTENTS YOU WILL NEED 8mm (5/16”) hex head socket WARNING WARNING • It is recommended that the door is reversed by a qualified technician due to the complexity of the process. • This kit contains parts for various different models. Not all parts will be required to be used. • Identify the parts required for your application and then put the excess components aside. • To install the handle, please refer to the Handle Installation instructions.
GENERAL DESCRIPTION Top hinge cover Cover Top hinge Plug Left hand cabinet shown 4 Door closer Cover foot Bottom hinge Stability foot Roller assembly Roller assembly GENERAL DESCRIPTION
CABINET TOP Removing old top hinge 1. Unplug appliance from power source 2. Ensure appliance is empty of all loose items 3. Remove screw from top hinge cover using Phillips head screw driver • Retain screw for later WARNING WARNING Door is no longer attached to cabinet 6. Slightly open the door and lift door vertically off bottom hinge and store in an upright position to prevent damage 7. Using a flat screw driver, remove Cover and reposition to other side 4. Remove top hinge cover and discard 5.
CABINET BOTTOM Removing old bottom hinge Carefully lay the appliance down on its back on a piece of soft packing material 3. Remove 2 (outside) screws with washers using 8mm socket • Retain screws and washers for later • Remove roller assembly and put aside for later WARNING WARNING Your refrigerator is heavy. You may need assistance to lay it down and lift it back up 1. Wind height adjusting nut up 4. Remove 2 inside screws using 8mm socket • Retain screws for later • 2.
CABINET BOTTOM (CONTINUED) Fitting new stability foot 3. Clip roller assembly into stability foot 1. Select correct handed Stability foot assembly and coloured Foot Cover • Secure roller assembly with 2 (outside) screws and washers using 8mm socket, • Clip Foot Cover to Stability foot (Recommended torque 8Nm) 2. Fit Stability foot and cover with 2 inside screws using 8mm socket.
CABINET BOTTOM (CONTINUED) Removing old stability foot 1. Wind height adjusting nut up. 3. Remove 2 (outside) screws with washers using 8mm socket • Retain screws and washers for later. 4. Remove roller assembly and aside for later. 2. Align slots with screws. 5. Remove 2 inside screws using 8mm socket. • Retain screws for later. 6. Remove adjusting foot assembly and cover and discard.
CABINET BOTTOM (CONTINUED) Fitting new bottom hinge 4. Clip roller assembly into hinge assembly. 1. Select correct handed hinge. 2. Align hinge with edge of cabinet and position hinge 3mm from edge of cabinet. 5. Secure roller assembly with 2 (outside) screws and washers using 8mm socket (recommended torque 8Nm). 6. Carefully stand cabinet up. WARNING WARNING 3. Fit hinge with 2 inside screws using 8mm socket (recommended torque 8Nm). Your refrigerator is heavy.
DOOR PREPARATION Door preparation - top Door preparation - bottom 1. Place door face down on a soft flat surface to prevent damage. 1. Remove screw from door closer at bottom of door using Phillips head screw driver. • retain screw 2. Remove plug from top of door using flat screw driver and fit to other side. 2. Remove door closer using flat screw driver and discard. 3. Select correct handed and coloured door closer. 4. Fit new door closer with screw to other side. Grease 5.
DOOR TO CABINET ASSEMBLY 1. Select correct handed hinge. 2. Place top hinge on top of cabinet. 3. Drive rear screw in half way using battery drill with 8mm socket. 8. Align door. • Align handle side of door at top to be flush with cabinet. • Set door gasket gap (hinge side) to 9mm. 9mm NOTE: Tapping plate is not threaded. Screw is a thread forming screw. 9. Tighten all 3 top hinge screws (recommended torque 8Nm). 10. Select correct handed and coloured hinge cover. 4.
TROUBLE SHOOTING GUIDE Trouble shooting guide CONCERN Door alignment WHAT TO DO Check bottom hinge alignment. Check top hinge alignment. Door not closing properly Check door gasket gap and top hinge alignment. Door gasket no seal Check door gasket gap and top hinge alignment. Door gasket noisy Check door gasket gap and top hinge alignment. Ensure there is nothing that nothing is preventing the door from closing such as aplliance contents or items placed near the appliance.
NOTES NOTES 13
NOTES 14 NOTES
NOTES NOTES 15
For more information on all Westinghouse appliances, or for dimension and installation information, call into your retailer, phone or email our customer care team or visit our website: AUSTRALIA phone: 1300 363 640 fax: 1800 350 067 email: customercare@electrolux.com.au web: westinghouse.com.au NEW ZEALAND phone: 0800 436 245 fax: 0800 225 088 email: customercare@electrolux.co.nz web: westinghouse.co.