Dimension Sheet

Dimension and installation guide
© 2020 Electrolux Home Products Pty Ltd. ABN 51 004 762 341. WDIM_Aspire_Apr20
IMPORTANT
These dimensions are a guide only. All measurements are in millimetres (mm).
For complete installation instructions, refer to the manual provided with product.
westinghouse.com.au
Slide out rangehoods
WRH605IS/IW
Product WxHxD (mm) 598 x 175 x 300
Fascia Height (mm) 40
Duct, diameter (mm) top only, 125
4
INSTALLATION
Standard ducting installation
The rangehood must be positioned at a minimum
clearance of 600mm for an electric cooktop and 650mm
for a gas cooktop. the rangehood should be no further
than 800mm from the cooktop, otherwise the unit
becomes less effective as the distance from the cooking
surface to the rangehood increases.
650
GAS
ELECTRIC
600
Fixing point dimensions – 600mm
REHR6* WRH605I* WRH608I*
470
598
210
280
158
175
121
2 0
40
40
ø
WRR614SA
470
598
210
280
158
175
121
2 0
70
70
ø
Fixing point dimensions – 900mm
ø
770
900
210
20
280
158
175
121
40
40
WARNING!
Failure to install the screws or fixing device in
accordance with these instructions may result in
electrical hazards.
Ducting installation
When installing with ducting pipe the Duct spigot must
be fitted to the ducting hole on top of the body of the
rangehood.
Duct Spigot
Recirculating installation
(For Models: WRH608I* WRR614*A & WRH908I*)
When installed in recirculating mode the ducting hole
cover must be fitted.
Ducting hole cover
Parts supplied with hood
1 × Duct Spigot
1 × Ducting hole cover (only for WRH608I*
WRR614*A and WRH908I*)
4 × M6 × 40 screws
4 × Ø6 washers
2 × Carbon filters (only for WRR614*A)
Parts to be purchased
• Aluminium tape or cable ties to secure flue pipe
• Custom drawer fascia (if required)
• Ducting accessories
underside of
rangehood
top of cooking
surface
if the cooktop
manufacturer
specifies
a greater
clearance
then that
must be used
4
INSTALLATION
Standard ducting installation
The rangehood must be positioned at a minimum
clearance of 600mm for an electric cooktop and 650mm
for a gas cooktop. the rangehood should be no further
than 800mm from the cooktop, otherwise the unit
becomes less effective as the distance from the cooking
surface to the rangehood increases.
650
GAS
ELECTRIC
600
Fixing point dimensions – 600mm
REHR6* WRH605I* WRH608I*
470
598
210
280
158
175
121
2 0
40
40
ø
WRR614SA
470
598
210
280
158
175
121
2 0
70
70
ø
Fixing point dimensions – 900mm
ø
770
900
210
20
280
158
175
121
40
40
WARNING!
Failure to install the screws or fixing device in
accordance with these instructions may result in
electrical hazards.
Ducting installation
When installing with ducting pipe the Duct spigot must
be fitted to the ducting hole on top of the body of the
rangehood.
Duct Spigot
Recirculating installation
(For Models: WRH608I* WRR614*A & WRH908I*)
When installed in recirculating mode the ducting hole
cover must be fitted.
Ducting hole cover
Parts supplied with hood
1 × Duct Spigot
1 × Ducting hole cover (only for WRH608I*
WRR614*A and WRH908I*)
4 × M6 × 40 screws
4 × Ø6 washers
2 × Carbon filters (only for WRR614*A)
Parts to be purchased
• Aluminium tape or cable ties to secure flue pipe
• Custom drawer fascia (if required)
• Ducting accessories
underside of
rangehood
top of cooking
surface
if the cooktop
manufacturer
specifies
a greater
clearance
then that
must be used