User manual

19. Place the bottom hinge LH (kit content) onto the
cabinet, placing it down then towards cabinet to
install. Replace the screw.
1
2
20. Replace the hinge foot onto the LH bottom hinge
and tighten with screw.
21. Replace the bottom door by holding at 45º and
gently slide onto the bottom hinge and close the
door.
45º
22. Replace LH centre hinge (kit content) by lifting the
door slightly and sliding hinge into the door and
placing the door down again.
1
2
23.
Insert 2 x 8 mm screws from existing centre hinge
into the LH centre hinge, tighten the screw until the
bracket is secured. Assemble 2 phillips head screws
and covers (kit content) on the other side as shown
below.
screws
screws
& covers
24. Replace the top door by holding at 45º and gently
slide onto the centre hinge and close the door.
45º
25. Slide the LH top hinge (kit content) into the door,
loosely screw the 3 x 8mm screws from the existing
top hinge in the cabinet.
Follow Step 12 – 16 for model WTB2300 and
WTB2500 where fitted with kick plate. For other
models without kick plate please skip to Step 17
and onwards.
12. Unscrew the four screws indicated below to remove
the side kickplates.
13. Unscrew the bottom hinge screw shown, pull the
hinge away from cabinet then up to remove.
1
2
14. Place the bottom hinge LH (kit content) onto the
cabinet, placing it down then towards cabinet to
install. Replace the screw.
1
2
15. Remove the spacer from the kickplate and clip to the
other side.
16. Assemble the kickplate to the refrigerator using the
four screws.
Skip Steps 17 to 20 and follow from Step 21 & onwards.
17. Unscrew the hinge foot using phillips head
screwdriver and unscrew foot on opposite side. Do
not discard.
18. Unscrew the bottom hinge screw shown, pull the
hinge away from cabinet then up to remove.
1
2
26. Ensure that the edges of the doors are parallel with
the sides of the cabinet.
27. Ensure that the bottom door and the top door have
a parallel gap.
28. Fully tighten the LH top hinge to the cabinet until the
hinge is secure.
29. Clip the LH hinge cover (kit content) over LH
top hinge.
30. Insert the RH top hinge hole cap (Kit content) in the
cabinet as shown.
31. Stand the refrigerator upright.
WARNING
Your refrigerator is heavy – you may need assistance.
33. Level the cabinet by adjusting the foot.
** It is recommended to apply a small amount of silicone
grease (Molykote EM-50L or equivalent – not provided with
kit) on all pivoting pin of left hand hinges for lubrication.
For further information on these appliances, or to obtain detailed dimension and installation information, call into your Retailer, phone or email our Customer Care team or visit our website:
© 2014 Electrolux Home Products Pty Ltd ABN 51 004 762 341 GMAN_DOORREV_May14 Part number: 807557701
AUSTRALIA
phone: [phone]
fax: [phone]
email: [e-mail]
web: www.westinghouse.com.au
VIETNAM
domestic toll free: 1800 58 88 99
phone: [phone]
fax: [phone]
email: [e-mail]
NEW ZEALAND
phone: [phone]
fax: [phone]
email: [e-mail]
web: www.westinghouse.co.nz
MALAYSIA
domestic toll free: 1300 881 122
fax: [phone]
email: [e-mail]
SINGAPORE
customer care hotline: [phone]
HONG KONG
phone: [phone]
email: [e-mail]
web: www.electrolux.com.hk